Gap formation of composite resin restorations is a serious shortcoming in clinical practice. Polymerization shrinkage stress exceeds the tooth-restoration bond strength, and it causes bacterial infiltration within gaps between cavity walls and the restorative material. Thus, an intermediate liner application with a low elastic modulus has been advised to minimize polymerization shrinkage as well as gap formation.Objective:The purpose of this in vitro study was to assess gap formation volume in premolars restored with different bulk-fill composites, with and without a resin-modified glass-ionomer cement (RMGIC) liner, using x-ray micro-computed tomography (micro-CT).Methodology:Sixty extracted human maxillary premolars were divided into six groups according to bucco-palatal dimensions (n=10). Standardized Class II mesio-occluso-distal cavities were prepared. G-Premio Bond (GC Corp., Japan) was applied in the selective-etch mode. Teeth were restored with high-viscosity (Filtek Bulk Fill, 3M ESPE, USA)-FB, sonic-activated (SonicFill 2, Kerr, USA)-SF and low viscosity (Estelite Bulk Fill Flow, Tokuyama, Japan)-EB bulk-fill composites, with and without a liner (Ionoseal, Voco GmbH, Germany)-L. The specimens were subjected to 10,000 thermocycles (5-55°C) and 50,000 simulated chewing cycles (100 N). Gap formation based on the volume of black spaces at the tooth-restoration interface was quantified in mm3 using micro-computed tomography (SkyScan, Belgium), and analyses were performed. Data were analyzed using repeated-measures ANOVA and the Bonferroni correction test (p < 0.05).Results:The gap volume of all tested bulk-fill composites demonstrated that Group SF (1.581±0.773) had significantly higher values than Group EB (0.717±0.679). Regarding the use of a liner, a significant reduction in gap formation volume was observed only in Group SFL (0.927±0.630) compared with Group SF (1.581±0.773).Conclusion:It can be concluded that different types of bulk-fill composite resins affected gap formation volume. Low-viscosity bulk-fill composites exhibited better adaptation to cavity walls and less gap formation than did sonic-activated bulk-fill composites. The use of an RMGIC liner produced a significant reduction in gap formation volume for sonic-activated bulk-fill composites.

No abstract

SUMMARY This laboratory study was designed to evaluate the marginal adaptation of Class II mesio-occluso-distal (MOD) restorations at the cervical region with micro-computed tomography (micro-CT). Two groups of restorations were compared: 1) those that had been exposed to radiotherapy before restoration was performed using a universal adhesive in etch-and-rinse and self-etch modes; and 2) those that had previously been restored using a universal adhesive in etch-and-rinse and self-etch modes and had subsequently undergone radiotherapy. Sixty intact human molars were randomly divided into groups according to irradiation status: no radiotherapy (control group); radiotherapy followed by restoration (radiotherapy-first group); and restoration followed by radiotherapy (restoration-first group). These three groups were then subdivided into two groups each on the basis of adhesive application type (etch-and-rinse and self-etch modes), for a total of six groups (n=10/group). Standardized Class II MOD cavities were prepared. A universal adhesive (Clearfil Universal Bond Quick, Kuraray, Okayama, Japan) was applied. The teeth were restored with resin composite (Estelite Posterior Quick, Tokuyama, Tokyo, Japan). The radiotherapy protocol was conducted with 60 gray (Gy) at 2 Gy/day, five days a week for six weeks. Adhesive defects were analyzed in distal and mesial views and evaluated with micro-CT (SkyScan 1174v2, Kontich, Antwerp, Belgium) on the basis of the volume of black spaces between the cavity walls and the restorative materials (mm3). The data were analyzed using the Kruskal-Wallis, Mann Whitney U and Wilcoxon tests (p&lt;0.05). The radiotherapy protocol did not affect the marginal adaptation of the universal adhesive at the cervical regions. Regarding the application modes, for the radiotherapy-first group, the self-etch mode caused significantly higher adhesive defects than the etch-and-rinse mode at the dentin margin. For the no-radiotherapy group, the adhesive defects at the dentin margin were significantly higher than at the enamel margin with the application of the etch-and-rinse mode.

The purpose of this in vitro study was to evaluate the effect of immediate dentin sealing (IDS) with and without chlorhexidine (CHX) pretreatment on the shear bond strength (SBS) of dual-cure adhesive resin cement. Mid-coronal dentin surfaces were obtained from 75 human molars. They were randomly allocated into five groups in accordance to type of IDS [etch&rinse/ER (Adper Single Bond2) and universal/U adhesive systems (Single Bond Universal)] and presence of CHX application (n = 15): Group ER; Group ER + CHX; Group U; Group U + CHX; and Group C (no IDS). Dualcure adhesive resin cements were bonded with a cylinder-shaped Teflon mold. The SBS was measured using a universal test machine. Fracture type was evaluated with stereomicroscope. The resin/dentin interfaces were examined with an environmental scanning electron microscope. Data were statistically analyzed with two-way analysis of variance and Bonferroni tests (p < .05). Regarding the IDS treatment groups with/ without CHX, there were no significant differences in SBS (p > .05). Group U + CHX showed significantly higher SBS than Group C (p < .05). Regarding the presence of CHX, no significant differences in SBS were found (p > .05). The prevalent failure mode was the mixed type for most of the groups. Group C exhibited an intact and regular hybrid layer with no resin tag, whereas longer and clear resin-tag formation was visible for Group U + CHX. CHX pretreatment improved the bond strength between adhesive resin cement and dentin when IDS treatment was performed with a universal adhesive system.

This study investigated the shear bond strength (SBS) of a universal adhesive to enamel/dentin; 1) that had undergone radiotherapy (RT) and 2) that were readily restored and had undergone RT. Enamel and dentin surfaces were obtained from 90 intact human molars. They were randomly divided into six groups according to the presence and timing of irradiation (RT0:no radiotherapy/control, RT1:RT before restoration, RT2:RT after restoration groups) and adhesive application modes (etch&rinse/ER, self-etch/SE)(n=15). A universal adhesive and resin composites were applied. The radiotherapy protocol was conducted with 60 Gy. The SBS test was subjected (1mm/min) and failure type analysis was performed. The resin-enamel/dentin interfaces were examined. Data were statistically analyzed. For enamel and dentin, the presence and timing of irradiation did not significantly influence the SBS values (p>0.05). For enamel, significantly higher SBS values were obtained using etch&rinse mode than self-etch mode (p<0.05). The predominant failure was mixed type. Loss of enamel prisms and obliterated irregular dentinal tubules were found for the radiotherapy-treated specimens. Resin tags were clearer in the irradiated enamel treated with ER than SE. Irradiation with different timings did not influence the bond strength to enamel and dentin, negatively. Irrespective of radiotherapy, the etch&rinse mode caused higher bond strength to enamel than self-etch mode.