Powered exoskeletons can empower paraplegics to stand and walk. Actively controlled hip ab/adduction (HAA) is needed for weight shift and for lateral foot placement to support dynamic balance control and to counteract disturbances in the frontal plane. Here, we describe the design, control, and preliminary evaluation of a novel exoskeleton, MINDWALKER. Besides powered hip flexion/extension and knee flexion/extension, it also has powered HAA. Each of the powered joints has a series elastic actuator, which can deliver 100 Nm torque and 1 kW power. A finite-state machine based controller provides gait assistance in both the sagittal and frontal planes. State transitions, such as stepping, can be triggered by the displacement of the Center of Mass (CoM). A novel step-width adaptation algorithm was proposed to stabilize lateral balance. We tested this exoskeleton on both healthy subjects and paraplegics. Experimental results showed that all users could successfully trigger steps by CoM displacement. The step-width adaptation algorithm could actively counteract disturbances, such as pushes. With the current implementations, stable walking without crutches has been achieved for healthy subjects but not yet for SCI paraplegics. More research and development is needed to improve the gait stability.

This paper evaluates the Achilles exoskeleton. The exoskeleton is intended to provide push-off assistance for healthy subjects during walking. The assistance is provided by a series elastic actuator that has been optimized to provide maximal push-off power. The paper presents the control method of the exoskeleton and the evaluation of the exoskeleton.

In this paper, we present the design, control, and preliminary evaluation of the Symbitron exoskeleton, a lower limb modular exoskeleton developed for people with a spinal cord injury. The mechanical and electrical configuration and the controller can be personalized to accommodate differences in impairments among individuals with spinal cord injuries (SCI). In hardware, this personalization is accomplished by a modular approach that allows the reconfiguration of a lowerlimb exoskeleton with ultimately eight powered series actuated (SEA) joints and high fidelity torque control. For SCI individuals with an incomplete lesion and sufficient hip control, we applied a trajectory-free neuromuscular control (NMC) strategy and used the exoskeleton in the ankle-knee configuration. For complete SCI individuals, we used a combination of a NMC and an impedance based trajectory tracking strategy with the exoskeleton in the ankle-knee-hip configuration. Results of a preliminary evaluation of the developed hardware and software showed that SCI individuals with an incomplete lesion could naturally vary their walking speed and step length and walked faster compared to walking without the device. SCI individuals with a complete lesion, who could not walk without support, were able to walk with the device and with the support of crutches that included a push-button for step initiationOur results demonstrate that an exoskeleton with modular hardware and control allows SCI individuals with limited or no lower limb function to receive tailored support and regain mobility.

This paper presents the Achilles exoskeleton, an autonomous ankle exoskeleton that can generate 52% of the positive plantarflexion power around the ankle of a 80 kg individual with only 1.5 kg of mass added around the ankle joint. The mass of the exoskeleton is lower and the power density is higher than that of existing autonomous exoskeletons. This high power density was achieved by designing a series elastic actuator that consists of an electric motor and ball-screw gear with a carbon fiber reinforced leaf-spring as lever-arm. A dynamic model that includes the motor and gear properties, spring stiffness, and exoskeleton geometry was used to optimize the design parameters for positive power injection. Doing this for multiple combinations of preselected motors and gears and comparing their support to weight ratio, revealed the best drive combination. The performance of the realized exoskeleton was assessed in several tests. The actuator can track the optimized actuator stroke trajectory with a following error that has a RMS of 2.3 mm, it can track force reference signals with amplitudes of 1 N to 100 N with a bandwidth between 8.1 Hz and 20.6 Hz, and it outputs a maximum mechanical power of 80.2 W. These results show that the device is suitable for fulfilling its purpose: reducing the metabolic cost of walking with an autonomous device.

Abstract. There is a lack of agreement in the literature as to what exactly quantifies the performance of underactuated hands. This paper proposes two benchmark tests to measure the ability of underactuated hands to grasp different objects and the ability to hold the objects when force disturbances apply. The first test determines the smallest and largest cylindrical object which can be successfully grasped in an enveloping grasp or in a pinch grasp. The second test provides the maximal allowable force which can be applied to a grasped object without loosing it. A setup was constructed consisting of standard components. Exemplary tests were applied to the Delft Hand 2. The proposed benchmark tests are representative to quantify the performance of pick and place operations with underactuated hands. The results of the tests can be applied to evaluate, compare, and improve the performance of robotic hands.