No abstract

One key step of the industrial development of a tidal energy device is the testing of scale prototype devices within a controlled laboratory environment. At present, there is no available experimental protocol which addresses in a quantitative manner the differences which can be expected between results obtained from the different types of facilities currently employed for this type of testing. As a consequence, where differences between results are found it has been difficult to confirm the extent to which these differences relate to the device performance or to the test facility type.In the present study, a comparative "Round Robin" testing programme has been conducted as part of the EC FP VII MaRINET program in order to evaluate the impact of different experimental facilities on the test results. The aim of the trials was to test the same model tidal turbine in four different test facilities to explore the sensitivity of the results to the choice of facility. The facilities comprised two towing tanks, of very different size, and two circulating water channels.Performance assessments in terms of torque, drag and inflow speed showed very similar results in all facilities. However, expected differences between the different tank types (circulating and towing) were observed in the fluctuations of torque and drag measurements. The main facility parameters which can influence the behaviour of the turbine were identified; in particular the effect of blockage was shown to be significant in cases yielding for high thrust coefficients, even at relatively small blockage ratios.

A passive solar still with separate condenser has been modeled and its performance evaluated. The system has one basin in the evaporation chamber and two basins (middle and upper) in the condenser chamber, with a glass cover over the evaporator basin and an opaque condensing cover over the upper basin. The evaporator, middle and upper basins yield the first, second and third effects respectively. The top part of the condensing cover is shielded from solar radiation to keep the cover relatively cool. Water vapor from the first effect condenses under the glass cover while the remainder of it flows into the condenser, by purging and diffusion, and condenses under the liner of the middle basin. The performance of the system is evaluated and compared with that of a conventional solar still under the same meteorological conditions. Results show that the distillate productivity of the present still is 62 % higher than that of the conventional type. Purging is the most significant mode of vapor transfer from the evaporator into the condenser chamber. The first, second and third effects contribute 60, 22 and 18 % of the total distillate yield respectively. It is also found that the productivity of the solar still with separate condenser is sensitive to the absorptance of the evaporator basin liner, mass of water in the evaporator and middle basins, and wind speed. The mass of water in the upper basin has a marginal effect on distillate production. Other results are presented and discussed in detail.

The flow developed on a tidal site can be characterized by combinations of turbulence, shear flows, and waves. Horizontal-axis tidal turbines are therefore subjected to dynamic loadings that may compromise the working life of the rotor and drive train components. To this end, a series of experiments were carried out using a 0.9 m horizontal-axis tidal turbine in a tow tank facility. The experiments included two types of regular waveforms, one of them simulating an extreme wave case, the other simulating a more moderate wave case. The second regular wave was designed to match the peak period and significant wave height of an irregular wave which was also tested. Measurements of torque, thrust, and blade-bending moments were taken during the testing campaign. Speed and torque control strategies were implemented for a range of operational points to investigate the influence that a control mode had in the performance of a tidal stream turbine. The results showed similar average power and thrust values were not affected by the control strategy, nor the influence of either the regular or irregular wave cases. However, it was observed that using torque control resulted in an increase of thrust and blade root bending moment fluctuations per wave period. The increase in fluctuations was in the order of 40% when compared to the speed control cases.

The prospects for urban wind power are discussed. A roof-mounted ducted wind turbine, which uses pressure differentials created by wind flow around a building, is proposed as an alternative to more conventional approaches. Outcomes from tests at model and prototype scale are described, and a simple mathematical model is presented. Predictions from the latter suggest that a ducted turbine can produce very high specific power outputs, going some way to offsetting its directional sensitivity. Further predictions using climate files are made to assess annual energy output and seasonal variations, with a conventional small wind turbine and a photovoltaic panel as comparators. It is concluded that ducted turbines have significant potential for retro-fitting to existing buildings, and have clear advantages where visual impact and safety are matters of concern.