As a major global pest, fall armyworm (FAW), Spodoptera frugiperda, invaded China in 2019, which has seriously threatened the safety of China's food production and raised widespread concerns. As a new low-volume application technology, an unmanned aerial spray system (UASS) is playing an important role in the control of FAW in China. However, the studies on the effect of the water application volume on the efficacy of FAW using UASS have been limited. In this study, Kromekote® cards were used to sample the deposition. The method of using a sampling pole and sampling leaf for the determination of deposition. Four water application volumes (7.5, 15.0, 22.5, and 30.0 L/ha) were evaluated with regard to the corn FAW control efficacy. A blank control was used as a comparison. The control efficacy was assessed at 1, 3, 7, and 14 days after treatment (DAT). The tested results showed that sampling methods have a significant effect on deposition results. The number of spray deposits and coverage on the sampling pole were 35 and 40% higher than those on the sampling leaves, respectively. The deposition and control efficacy gradually increased as the water application volume increased. The control efficacy at 14 DAT under different water application volumes was in the range of 59.4–85.4%. These data suggest that UASS spraying can be used to achieve a satisfying control of FAW, but the control efficacy of the water application volume of 30.0 and 22.5 L/ha did not differ significantly. Considering work efficiency, a water application volume of 22.5 L/ha is recommended for field operation.

The use of drones in agriculture is expanding at a brisk pace in crop production due to the superiority in precision, efficiency, and safety of their applicators. However, their potential drift risk also raises concern for users and regulatory authorities. The method of wind tunnel research can effectively evaluate the weighted influence of each drift factor, especially the drift characteristics of the nozzle and spray solution. Based on the wind tunnel test results, centrifugal nozzles have a higher drift risk than hydraulic nozzles, even with a similar DV50. The cumulative drift rate of the centrifugal nozzle at 2 m downwind was 90.1% compared to the LU12001 nozzle’s 40.6% under the wind speed of 3.5 m/s. Compared with the same coding as the flat fan hydraulic nozzle, the IDK nozzle can effectively reduce the drift rate. For the tested nozzles, DV50 and wind speed had a linear relationship with drift rate, and the sampling location had an exponential or logarithmic relationship with drift rate. Spray adjuvants, especially modified vegetable oils, had a significant effect on reducing the amount of drift. The results of this experiment provide a reference for the selection of nozzles and the addition of spray adjuvants. Further clarifying the spray drift characteristics of drones until a drift prediction model is available is still the focus of research.

As an effective supplement to ground machinery, UAVs play an important role in agriculture and have become indispensable intelligent equipment in the development of precision agriculture. Various types of agricultural UAV-based spreading devices, mainly disc-type and pneumatic-type, have appeared in domestic and foreign markets. UAV-based rice topdressing has gradually become a widely recognized application with great market potential. In the process of UAV-based low-altitude fertilization, due to the existence of the rotor wind field, the environment for particle air diffusion is complex, and the movement trajectory and deposition distribution of fertilizer are affected by many factors, resulting in large differences in the spreading. The flight height and speed have a great influence on particle movement and deposition, and a reasonable combination of work parameters can be used for efficient and high-quality particle deposition. In order to obtain better particle deposition distribution, this paper uses the method of a single flight line to test and analyze the characteristics of particle deposition distribution for fertilization using multi-rotor UAVs at different flight heights and speeds. The effective swath width and deposition uniformity obtained via the simulation of overlapped route superposition were used to optimized the appropriate work parameters to ensure that a reasonable and effective deposition amount can be obtained during actual application. The results show that the flight height and speed and the interaction of both have an important influence on the deposition amount and the effective width, but it is not a simple linear relationship. On the whole, as the flight height increases, the coefficient of variation decreases and the effective width increases, but it is not obvious when the speed is low. For the R20, when the flight speed is 2 m/s, the effective width first increases and then decreases with the increase in flight height, and the difference in the deposition amount at a height of 5 m is larger than that at other heights. Under the three working heights, the effective swath width is the same when the flight speed is 4 m/s and 6 m/s, and the effective swath width is also the same when the speed is 7 m and 9 m. For the T16, when the flight speed is 4 m/s, the deposition uniformity is relatively good, and the effective width increases with the increase in flight height. Therefore, the combination of 7–6 m/s and 9–4 m/s parameters will be the best operating parameters for R20 and T16. However, considering the actual dynamic meteorological environment in the field, the operating height can be appropriately lowered according to the influence of the crosswind during actual operation. The research results of this paper can provide scientific reference and suggestions for further improving the effect of UAV-based fertilization.

The droplet size distribution following pesticide application practices can significantly impact droplet drift and non-target organisms (animals and plants). However, the relationship among liquid sheet breakup, drop formation, and droplet drift is an area that has been studied over the past 65 years but is still not fully understood. The objectives of this study were severalfold: to examine the liquid sheet breakup following the use of different adjuvants (sodium dodecyl sulfate, aerosol OT, and silicone at 1%) and their effects on the drift via three commonly used commercial spray nozzles (XR, AIXR, and TXVK). The spray sheet and initial droplet size spectrum for each spray was detected by a particle image velocimetry (PIV) system, and the drift for each treatment was measured in a wind tunnel. The nozzle type and the spray solution were found to significantly affect the liquid sheet breakup characteristics. AIXR produced large droplets, and TXVK with short liquid sheet length produced more small droplets. All adjuvants used in these experiments increased the formation of large droplets upon atomization while simultaneously reducing driftable fines (e.g., drops %<150 µm). The drift potential can be reduced by up to 66.1% when switching from a fine spray quality (TXVK) to a coarse spray quality (AIXR). The SDS adjuvant provided the most effective drift reduction for XR and TXVK nozzles showing reduced drift potential by 69.2% and 66.3%, respectively, while the silicone adjuvant showed the largest drift reduction for AIXR of 78.3%. The correlation between the liquid sheet length and DV0.5 was positive for XR and TXVK nozzles, and there was a significant positive correlation between %<150 µm and drift potential for all nozzles. This work suggests that the drift can be reduced significantly by changing the nozzle type and adding pesticide adjuvant into spray solution, which provided data support for the drift reduction of plant protection drones.