Material properties and their variations in individual bone organs are important for understanding bone adaptation and quality at a tissue level, and are essential for accurate mechanical models. Yet material property variations have received little systematic study. Like all other material property studies in individual bone organs, studies of the human mandible are limited by a low number of both specimens and sampled regions. The aims of this study were to determine: 1) regional variability in mandibular material properties, 2) the effect of this variability on the modeling of mandibular function, and 3) the relationship of this variability to mandibular structure and function. We removed 31 samples on both facial and lingual cortices of 10 fresh adult dentate mandibles, measured cortical thickness and density, determined the directions of maximum stiffness with a pulse transmission ultrasonic technique, and calculated elastic properties from measured ultrasonic velocities. Results showed that each of these elastic properties in the dentate human mandible demonstrates unique regional variation. The direction of maximum stiffness was near parallel to the occlusal plane within the corpus. On the facial ramus, the direction of maximum stiffness was more vertically oriented. Several sites in the mandible did not show a consistent direction of maximum stiffness among specimens, although all specimens exhibited significant orthotropy. Mandibular cortical thickness varied significantly (P < 0.001) between sites, and decreased from 3.7 mm (SD = 0.9) anteriorly to 1.4 mm posteriorly (SD = 0.1). The cortical plate was also significantly thicker (P < 0.003) on the facial side than on the lingual side. Bone was 50-100% stiffer in the longitudinal direction (E(3), 20-30 GPa) than in the circumferential or tangential directions (E(2) or E(1); P < 0.001). The results suggest that material properties and directional variations have an important impact on mandibular mechanics. The accuracy of stresses calculated from strains and average material properties varies regionally, depending on variations in the direction of maximum stiffness and anisotropy. Stresses in some parts of the mandible can be more accurately calculated than in other regions. Limited evidence suggests that the orientations and anisotropies of cortical elastic properties correspond with features of cortical bone microstructure, although the relationship with functional stresses and strains is not clear.

Elastic constants, including the elastic modulus, the shear modulus, and Poisson's ratio, were measured on human craniofacial bone specimens obtained from the supraorbital region and the buccal surfaces of the mandibles of unembalmed cadavers. Constants were determined using an ultrasonic wave technique in three directions relative to the surface of each sample: 1) normal, 2) tangential, and 3) longitudinal. Statistical analysis of these elastic constants indicated that significant differences in the relative proportions of elastic properties existed between the regions. Bone from the mandible along its longitudinal axis was stiffer than bone from the supraorbital region. Directional differences in both locations demonstrated that cranial bone was not elastically isotropic. It is suggested that differences in elastic properties correspond to regional differences in function.

Ridge resorption following edentulation has been documented clinically, but the effects of tooth loss on the material properties of mandibular cortical bone have received little study. Material properties and their structural basis are essential for our understanding of bone quality in the edentulous mandible and are of interest as a tissue-level model for functional adaptation. This study's aim was to determine material property variability in the edentulous mandible, and to compare it with data from a previous study of dentate mandibles. Forty-four cortical samples were removed from each of 10 adult fresh edentulous mandibles. Cortical thickness and density were measured. Material properties were calculated from ultrasonic velocities. Mandibular cortical bone in the edentulous mandibles differed from that of dentate mandibles in cortical thickness, elastic and shear moduli, anisotropy, and orientation of the axis of maximum stiffness. These results suggest that cortical microstructural changes accompany ridge resorption following edentulation.

Ultrasonic determination of elastic properties in human craniofacial cortical bone is problematic because of a lack of information about the principal material axes, and because the cortex is often thinner than in long bones. This study investigated solutions that permit reasonable determination of elastic properties in the human mandible. We tested whether ultrasonic velocities could be reliably measured in cylindrical samples of aluminum and mandibular bone, and the effects of reduced specimen thickness. Results indicted that (1) varying shape had minimal effects on ultrasonic velocities or derived elastic properties, and (2) ultrasonic velocities have relatively increased measurement error as propagation distances decreased. The increased error in velocity measurements of mandibular cortical specimens of less than 1.2 mm in thickness should be considered when assessing the reliability of single measurements.