PurposeThis study compared subcutaneous adipose tissue (SAT) measurements using a skinfold caliper and Renco Lean-Meater Series 12 A-mode portable ultrasound scanner (A-US). It aimed to assess their inter- and intra-rater reliability and measure the agreement between both methods.MethodsEighty-four volunteers of different fitness levels were divided into three groups by Ʃ6 skinfolds: G1 ≤ 55 mm (n = 33 males); G2 > 55 mm (n = 32 males); G3 = 98.0 ± 52.3 mm (n = 19 females). Triceps, subscapular, biceps, iliac crest, supraspinal, abdominal, front thigh and medial calf were assessed by ultrasound and skinfolds. Two technicians for both tools performed triplicate measures. Intraclass correlation (ICC), technical error of measurement (TEM) and coefficients of variation (CVs) were applied for test-retest and inter-rater reliability. Non-Parametric statistics were used in order to establish possible statistical differences and correlation between skinfolds thickness and uncompressed subcutaneous adipose tissue thickness from ultrasound. The amount of agreement between both methods was assessed with Lin’s coefficient and a scatterplot of all site locations. A Bland-Altman plot was constructed to establish limits of agreement between groups and regression analysis was employed to assess the ability of skinfolds to explain the variance of ultrasound.ResultsTest-retest ICC for skinfolds and ultrasound were higher than 0.989 and 0.793, respectively. Inter-rater ICC for skinfolds was 0.999 with a 95% CI of 0.995 to 0.999 and for ultrasound was 0.755 with a much larger 95% CI of 0.622 to 0.841. TEMs (> 8.50%) and CVs (> 6.72%) compromised ultrasound reliability. Statistical differences were found in most of the analysed anatomical sites (p < 0.001) except in biceps G2 (Z = -1.150, p = 0.25) and G3 (Z = -1.309, p = 0.19). Good correlations (r > 0.7, p ≤ 0.05) were reported at almost all anatomical sites and groups except for biceps (G1: Rho = 0.26, p = 0.140) and abdominal (G2: Rho = -0.16, p = 0.38; G3: Rho = 0.43, p = 0.068). Lin’s concordance correlation coefficient registered low values of agreement between skinfolds and A-mode ultrasound (ranged from—0.009–0.646). The scatterplot and the estimated regression line drawn through the midst of all anatomical sites of the whole sample had a slope of 0.51 and R2 adjusted = 0.62 was obtained. The combined analysis between the Bland-Altman plot and the linear regression showed that specifically in the G2 and G3 groups, as the SAT increases the differences between skinfolds and ultrasounds measurements also increases.ConclusionsThe Renco Lean-Meater ultrasound is not interchangeable with skinfold measures. Its utility is questionable, particularly for assessing SAT in active adult populations. Its poor test-retest and inter-rater reliability as well as the lack of agreement when compared to the skinfolds would exclude the free use of the A-mode ultrasound scanner in its hypothetical replacing of the classical calipers.

Inertial measurement units (IMUs) represent a technology that is booming in sports right now. The aim of this study was to evaluate the validity of a new application on the use of these wearable sensors, specifically to evaluate a magnet-based timing system (M-BTS) for timing short-duration sports actions using the magnetometer built into an IMU in different sporting contexts. Forty-eight athletes (22.7 ± 3.3 years, 72.2 ± 10.3 kg, 176.9 ± 8.5 cm) and eight skiers (17.4 ± 0.8 years, 176.4 ± 4.9 cm, 67.7 ± 2.0 kg) performed a 60-m linear sprint running test and a ski slalom, respectively. The M-BTS consisted of placing several magnets along the course in both contexts. The magnetometer built into the IMU detected the peak-shaped magnetic field when passing near the magnets at a certain speed. The time between peaks was calculated. The system was validated with photocells. The 95% error intervals for the total times were less than 0.077 s for the running test and 0.050 s for the ski slalom. With the M-BTS, future studies could select and cut the signals belonging to the other sensors that are integrated in the IMU, such as the accelerometer and the gyroscope.

Small differences in turn cycle structure, invisible to the naked eye, could be decisive in improving descent performance. The aim of this study was to assess the influence of turn cycle structure on the performance of elite alpine skiers using an inertial measurement unit (IMU) in different slalom (SL) course settings. Four SL courses were set: a flat-turned (FT), a steep-turned (ST), a flat-straighter (FS) and a steep-straighter (SS). Five elite alpine skiers (21.2 ± 3.3 years, 180.2 ± 5.6 cm, 72.8 ± 6.6 kg) completed several runs at maximum speed for each SL course. A total of 77 runs were obtained. Fast total times correlate with a longer initiation (INI) time in FT, a shorter steering time out of the turn (STEOUT) in the FT and FS and a shorter total steering time (STEIN+OUT) in the FT and SS courses. The linear mixed model used for the analysis revealed that in the FT-course for each second increase in the INI time, the total time is reduced by 0.45 s, and for every one-second increase in the STEOUT and STEIN+OUT times, the total time increases by 0.48 s and 0.31 s, respectively. Thus, to enhance descent performance, the skier should lengthen the INI time and shorten the STEOUT and STEIN+OUT time. Future studies could use an IMU to detect turn phases and analyze them using the other built-in sensors.