The microstructure and the rheological properties of pure HM (high methoxyl) and LM (low methoxyl) pectin gels and of mixed HM/LM pectin gels have been investigated. Gel formation of either the HM or LM pectin, or both, was initiated in the mixed gels by varying the sucrose and Ca(2+) content. The microstructure was characterized by transmission electron microscopy, light microscopy, and confocal laser scanning microscopy. HM and LM pectin gels showed aggregated networks with large pores around 500 nm and network strands of similar character. Small differences could be found, such as a more inhomogeneous LM pectin network with shorter and more branched strands of flexible appearance. LM pectin also formed a weak gel in 60% sucrose in the absence of calcium. A highly inhomogeneous mixed gel structure was formed in the presence of 60% sucrose and Ca(2+) ions, which showed large synergistic effects in rheological properties. Its formation was explained by the behavior of the corresponding pure gels. In the presence of 60% sucrose alone, a homogeneous, fine-stranded mixed network was formed, which showed weak synergistic effects. It is suggested that LM pectin interacts with HM pectin during gel formation, thereby hindering secondary aggregation leading to the aggregated networks observed for the pure gels.

The kinetic behavior during gel formation and the microstructure of 0.75% high methoxyl (HM) pectin gels in 60% sucrose have been investigated by oscillatory measurements and transmission electron microscopy for three comparable citrus pectin samples differing in their degree of blockiness (DB). Ca2+ addition at pH 3.0 resulted in faster gel formation and a lower storage modulus after 3 h for gels of the blockwise pectin A. For gels of the randomly esterified pectin B, the Ca2+ addition resulted in faster gel formation and a higher storage modulus at pH 3.0. At pH 3.5, both pectins A and B were reinforced by the addition of Ca2+. In the absence of Ca2+, the shortest gelation time was obtained for the sample with the highest DB. Microstructural characterization of the gel network, 4 and 20 h after gel preparation, showed no visible changes on a nanometer scale. The microstructure of pectins A and B without Ca2+ was similar, whereas the presence of Ca2+ in pectin A resulted in an inhomogeneous structure.

No abstract

The microstructure, kinetics of gelation, and rheological properties have been investigated for gels of nonamidated pectin (C30), amidated pectin (G), and saponified pectin (sG) at different pH values, both with and without sucrose. The low-methoxyl (LM) pectin gels were characterized in the presence of Ca(2+) by oscillatory measurements and transmission electron microscopy (TEM). The appearance of the gel microstructure varied with the pH, the gel structure being sparse and aggregated at pH 3 but dense and somewhat entangled at pH 7. During gel formation of pectins G and C30 at pH 3 there was a rapid increase in G' initially followed by a small increase with time. At pH 7 G' increased very rapidly at first but then remained constant. The presence of sucrose influenced neither the kinetic behavior nor the microstructure of the gels but strongly increased the storage modulus. Pectins G and C30 showed large variations in G' at pH values 3, 4, 5, and 7 in the presence of sucrose, and the maximum in G' in the samples occurred at different pH values. Due to its high Ca(2+) sensitivity, pectin sG had a storage modulus that was about 50 times higher than that of its mother pectin G at pH 7.

To test the hypothesis that the introduction of a hydrophilic hemicellulose would affect viscoelastic properties and increase water permeability, xyloglucan (XG) was adsorbed onto the surface of microcrystalline cellulose (MCC) in water dispersion prior to the extrusion of 79–80 wt % polylactide acid (PLA), 20 wt % MCC, and 0–1 wt % XG. For comparison, composites of PLA, MCC, and non‐absorbed XG were produced. Analysis of thermal properties showed no differences for glass‐transition or melting temperatures, but the crystallinity of the films increased with the addition of MCC and XG. Storage modulus of the composite materials increased with XG content; however, at higher humidities storage modulus decreased, probably because of lower interfacial adhesion. Water permeability through the films increased more with the addition of XG adsorbed to the MCC than with the MCC and XG simply mixed in the same amounts. © 2014 The Authors. Journal of Applied Polymer Science Published by Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41219.