No abstract

Geometric characterization of a geothermal reservoir's structures, and their relation to stress field orientation, is vital for resource development. Subsurface structure and stress field orientations of the Rotokawa Geothermal Field, New Zealand, have been studied, for the first time, using observations obtained from analysis of three acoustic borehole televiewer logs. While an overall NE-SW fracture strike exists, heterogeneity in fracture dip orientation is evident. Dominant dip direction changes from well to well due to proximity to variously oriented, graben-bounding faults. Fracture orientation heterogeneity also occurs within individual wells, where fractures clusters within certain depth intervals have antithetic dip directions to the well's dominant fracture dip direction. These patterns are consistent with expected antithetic faulting in extensional environments. A general S Hmax orientation of NE-SW is determined from induced features on borehole walls. However, numerous localized azimuthal variations from this trend are evident, constituting stress field orientation heterogeneity. These variations are attributed to slip on fracture planes evidenced by changes in the azimuth of drilling-induced tensile fractures either side of a natural fracture. Correlation of observed fracture properties and patterns to well permeability indicators reveal that fractures play a role in fluid flow in the Rotokawa geothermal reservoir. Permeable zones commonly contain wide aperture fractures and high fracture densities which have a dominant NE-SW strike orientation and NW dip direction. Studies of this kind, which show strong interdependency of structure and stress field properties, are essential to understand fluid flow in geothermal reservoirs where structural permeability dominates.

During the second phase of the Alpine Fault, Deep Fault Drilling Project (DFDP) in the Whataroa River, South Westland, New Zealand, bedrock was encountered in the DFDP-2B borehole from 238.5-893.2 m Measured Depth (MD). Continuous sampling and meso-to microscale characterization of whole rock cuttings established that, in sequence, the borehole sampled amphibolite facies, Torlesse Composite Terrane-derived schists, protomylonites, and mylonites, terminating 200-400 m above an Alpine Fault Principal Slip Zone (PSZ) with a maximum dip of 62°. The most diagnostic structural features of increasing PSZ proximity were the occurrence of shear bands and reduction in mean quartz grain sizes. A change in composition to greater mica:quartz+feldspar, most markedly below ~ 700 m MD, is inferred to result from either heterogeneous sampling or a change in lithology related to alteration. Major oxide variations suggest the fault-proximal Alpine Fault alteration zone, as previously defined in DFDP-1 core, was not sampled.

Fault rock assemblages reflect interaction between deformation, stress, temperature, fluid, and chemical regimes on distinct spatial and temporal scales at various positions in the crust. Here we interpret measurements made in the hanging‐wall of the Alpine Fault during the second stage of the Deep Fault Drilling Project (DFDP‐2). We present observational evidence for extensive fracturing and high hanging‐wall hydraulic conductivity (∼10−9 to 10−7 m/s, corresponding to permeability of ∼10−16 to 10−14 m2) extending several hundred meters from the fault's principal slip zone. Mud losses, gas chemistry anomalies, and petrophysical data indicate that a subset of fractures intersected by the borehole are capable of transmitting fluid volumes of several cubic meters on time scales of hours. DFDP‐2 observations and other data suggest that this hydrogeologically active portion of the fault zone in the hanging‐wall is several kilometers wide in the uppermost crust. This finding is consistent with numerical models of earthquake rupture and off‐fault damage. We conclude that the mechanically and hydrogeologically active part of the Alpine Fault is a more dynamic and extensive feature than commonly described in models based on exhumed faults. We propose that the hydrogeologically active damage zone of the Alpine Fault and other large active faults in areas of high topographic relief can be subdivided into an inner zone in which damage is controlled principally by earthquake rupture processes and an outer zone in which damage reflects coseismic shaking, strain accumulation and release on interseismic timescales, and inherited fracturing related to exhumation.