Aim: The aim of the present study was to evaluate the stress distribution around the titanium and zirconium implant with different abutment angulations in the anterior maxilla to off-axial load. Setting and Design: In vitro – Comparative study. Materials and Methods: Two models of titanium and zirconium implants (4 mm × 13 mm) and abutment with at 0°, 15°, 25° angulations were modeled to replace missing right central incisor using three-dimensional finite element analysis. A bite force of 178 N was applied on the lingual fossa of crowns at an angle of 120° off-axial to the long axis of implant. Statistical Analysis Used: Nil. Results: Von Misses stresses observed are as follows: (1) at the implant–bone interface Ti 0 (8.31 MPa), Zr 0 (8.57 MPa), Ti 15 (83.59 MPa), Zr 15 (98.07 MPa), Ti 25 (197.8 MPa), and Zr 25 (265.77 MPa); (2) at the implant–abutment interface Ti 0 (5.90 MPa), Zr 0 (6.45 MPa), Ti 15 (19.13 MPa), Zr 15 (19.32 MPa), Ti 25 (38.65 MPa), and Zr 25 (38.26 MPa); and (3) within superstructure Ti 0 (3.11 MPa), Zr 0 (5.02 MPa), Ti 15 (6.17 MPa), Zr 15 (5.02 MPa), Ti 25 (8.15 MPa), and Zr 25 (6.131 Mpa). Conclusion: Stress behavior of titanium and zirconium implant with tested abutment angulation at implant–abutment interface and within the superstructure was similar, except at implant–bone interface.
he rapid evolution of computer-aided design and computer-aided manufacturing (CAD-CAM) led to the introduction of newer materials that could be precisely milled for the fabrication of dental prostheses. PEEK (PolyEtherEtherKetone) has been explored for a number of applications for clinical dentistry, including removable dental prostheses, fixed dental prostheses, implant-supported prostheses, resin-bonded fixed dental prostheses and implant-retained overdentures. The major beneficial property of PEEK is its lower Young's modulus, and as elastic as bone, providing a cushioning effect and reduction of stress transferred to abutment teeth. It is a material with high biocompatibility, good mechanical properties, high-temperature resistance, chemical stability, polishability, good wear resistance, and high bond strength with luting cements. Further, PEEK is also recommended for a wide range of CAD-CAM fabricated fixed and removable prostheses, fabrication of occlusal splints, intra-radicular posts, implant abutments and provisional restorations. PEEK material shows a property of radiolucency, which is advantageous for the evaluation of both osseointegrationand tissue surrounding the implant on computed tomography. Considering these properties, PEEK is increasingly being used in implantology.
For the dental profession in general and in prosthodontists speciality, the subject of sleep medicine continues to offer great challenges and opportunities in diagnosis, treatment planning, and treatment based on qualitative evidence. Though the role contends by the prosthodontists is still in its infancy, there is a lot to find out and understand in the rapidly evolving field of sleep medicine because the recognition of co-managing patients with sleep disorders by the prosthodontists is quick changing into a reality. This article discusses the prosthodontic perspectives, particularly on obstructive sleep apnea.
Reliable bonding between the prepared tooth and monolithic ceramics can be achieved by various luting agents available on the market. The selection of luting agent and cementation technique plays an important role in the success of the restoration. With the advent of resin-based adhesive systems as luting agents, clinicians' perspectives have changed to a more conservative approach. Recent systems, chemically adhere athe crowns to the prepared tooth structure showing higher bond strength. To reach the aesthetic demands of the patients, all-ceramic restorations were considered over metal-ceramic crowns. Few all-ceramic crowns are brittle, the strength is dependent on the chemical structure and method of fabrication. While some all-ceramic restorations gain strength after cementation. Thus, the choice of luting agent used in cementing all-ceramic crowns is crucial. Even though many luting agents are being introduced no single luting agent fulfilled all the requirements. Among them, adhesive cements showed greater bond strength and enhanced the retention of minimal preparation, which are less retentive. Traditional non-adhesive agents can be used in retentive preparations that bond through mechanical means rather than the chemical bond seen in newer adhesive cements. Also, surface treatments of zirconia showed greater bond strengths irrespective of the luting agent being used. These include air abrasion, acid etching, applying silane couplers, and primers that increase the surface area for adhesion. The use of all-ceramic restorations, the need for surface treatments, types of surface treatments, adhesion and adhesive agents, and evidence from current in vitroresearch on monolithic ceramics and tooth adhesion were all discussed in this review.
Dental implants are becoming a more common treatment choice in recent years, with an increasing number of patients preferring this option. Proper implant positioning is the most significant requirement for a successful implant treatment prognosis. A transfer system is necessary to ensure logical continuity between the diagnosis, prosthetic preparation, and surgical phases. Various techniques have been proposed for the fabrication of surgical guide templates in implant dentistry. This paper aims to review the associated literature and recent advancements in this field based on the design concept.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.