A redox initiation system was used to efficiently enhance the mechanical behavior of macromolecular microsphere hydrogels.

In this investigation, carboxymethyl cellulose (CMC)‐reinforced poly(vinyl alcohol) (PVA) were prepared with trimethylol melamine as a chemical crosslinker. The structure and property of hydrogels were measured by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), texture analysis, and rheometry. The FTIR spectra demonstrated that the etherification reaction successfully occurred in the PVA–CMC hydrogels, and the SEM figures exhibited the homogeneous porous structure of the CMC–PVA hydrogels. The compression strength of the PVA–CMC hydrogels was 15 times higher than that of the PVA hydrogels. Moreover, the PVA–CMC hydrogels exhibited a higher storage modulus than that of the PVA hydrogels; this illustrated better elasticity for the PVA–CMC hydrogels. As a result, CMC‐modified PVA hydrogels with high mechanical behavior will broaden the potential applications of hydrogels, such as in wound dressings, facial masks, and skin‐protection layers. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44590.

Toughness, strechability and compressibility for hydrogels were ordinarily balanced for their use as mechanically responsive materials. For example, macromolecular microsphere composite hydrogels with chemical crosslinking exhibited excellent compression strength and strechability, but poor tensile stress. Here, a novel strategy for the preparation of a super-tough, ultra-stretchable and strongly compressive hydrogel was proposed by introducing core-shell latex particles (LPs) as crosslinking centers for inducing efficient aggregation of hydrophobic chains. The core-shell LPs always maintained a spherical shape due to the presence of a hard core even by an external force and the soft shell could interact with hydrophobic chains due to hydrophobic interactions. As a result, the hydrogels reinforced by core-shell LPs exhibited not only a high tensile strength of 1.8 MPa and dramatic elongation of over 20 times, but also an excellent compressive performance of 13.5 MPa at a strain of 90%. The Mullins effect was verified for the validity of core-shell LP-reinforced hydrogels by inducing aggregation of hydrophobic chains. The novel strategy strives to provide a better avenue for designing and developing a new generation of hydrophobic association tough hydrogels with excellent mechanical properties.

A new crosslinked amphoteric hydrogel (PAC) was synthesized and evaluated as an internal curing agent of concrete. PAC was prepared from acrylamide (AM) and 4-(2-((carboxylatomethyl)dimethylammonio)ethoxy)24-oxobut-2-enoate (CMD) through free-radical polymerization by using ammonium persulfate (APS) as an initiator and methylene-bisacrylamide (MBA) as a crosslinker. The structure of the prepared polymer was verified by the IR spectra. The effects of the polymerization variables on the swelling capacity of PAC were investigated. The water absorbency of PAC was found to increase with increasing CMD/AM ratio, reach a maximum value, and decrease afterword. Increase of either APS or MBA content decreased the water absorbency. The highest water absorbency of PAC hydrogel (P7) achieved in deionized water, 0.1M NaCl solutions and 0.1M CaCl 2 solutions, was 306 g/g, 32 g/g, and 22 g/g, respectively. Compared with a commercial acrylate-based hydrogel 283HA, P7 was less sensitive to the existence of Ca 21 ions in cement pore solutions, and more effective in reducing the cracking tendency of cement pastes. Finally, mortars incorporated with proper amounts of P7 showed smaller drying shrinkage and higher compressive strength than that without hydrogel present. V C 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42175.