In comparison to traditional in vitro cell culture in Petri dishes or well plates, cell culture in microfluidic-based devices enables better control over chemical and physical environments, higher levels of experimental automation, and a reduction in experimental materials. Over the past decade, the advantages associated with cell culturing in microfluidic-based platforms have garnered significant interest and have led to a plethora of studies for high throughput cell assays, organs-on-a-chip applications, temporal signaling studies, and cell sorting. A clear concern for performing cell culture in microfluidic-based devices is deciding on a technique to deliver and pump media to cells that are encased in a microfluidic device. In this review, we summarize recent advances in pumping techniques for microfluidic cell culture and discuss their advantages and possible drawbacks. The ultimate goal of our review is to distill the large body of information available related to pumps for microfluidic cell culture in an effort to assist current and potential users of microfluidic-based devices for advanced in vitro cellular studies.

Structural properties of the proton-exchanged forms of bis[(perfluoroalkyl)sulfonyl] imide (PFSI) ionomer materials were investigated. The hydration and dehydration of samples prepared as thin films and freestanding membrane were probed by applying transmission infrared spectroscopy. Spectral bands were assigned and effects of water incorporation into membrane pores and channels were understood by drawing upon results from related measurements performed on the structurally similar, perfluorosulfonic acid ionomer, Nafion. Both PFSI and Nafion membrane materials display a prominent infrared absorbance band near 1060 cm(-1) that arises from a vibrational mode of the ionizable group present on the side chains that extend from the poly(tetrafluoroethylene) backbone on the polymers. The mode can be traced to symmetric stretching of the -SO(3)(-) (sulfonate) group in Nafion and to antisymmetric S-N-S stretching within the sulfonyl imide end group (-SO(2)(N(-))SO(2)CF(3)) in the PFSI materials. For Nafion samples, the position and width of the band near 1060 cm(-1) are strongly sensitive to membrane hydration, whereas the band position and shape change only slightly during hydration and dehydration of PFSI materials. The possibility for greater charge delocalization over the sulfonyl imide moiety and shielding of hydrophilic species by the terminal -CF(3) group are suggested to explain the differences. These effects also likely influence the stretching modes of the side chain C-O-C groups. A pair of bands, sensitive to hydration and traceable to different C-O-C groups in a side chain, is present in the 970-990 cm(-1) region of Nafion. However, the two features are not well resolved and are less sensitive to hydration in spectra of PFSI samples. The most intense ionomer spectral bands arise from modes involving C-F stretching motion and appear between 1150 and 1250 cm(-1). Toward the high energy side of the envelope, there is substantial overlap with features of sulfonate group antisymmetric SO stretching modes in Nafion, but SO stretching modes of the sulfonyl imide moiety are higher in energy and better resolved in spectra of the PFSIs. During water uptake from a dry state into PFSI materials, a progression of features characteristic of solvated H(3)O(+) species appears across the water O-H stretching (2800-3800 cm(-1)) and H-O-H bending (1500-2000 cm(-1)) regions, similar to responses observed for water inside proton-exchanged Nafion.

In this work, we demonstrate DNA separation and genotyping analysis in gel-free solutions using a nanocapillary under pressure-driven conditions without application of an external electric field. The nanocapillary is a ~50-cm-long and 500-nm-radius bare fused silica capillary. After a DNA sample is injected, the analytes are eluted out in a chromatographic separation format. The elution order of DNA molecules follows strictly with their sizes, with the longer DNA being eluted out faster than the shorter ones. High resolutions are obtained for both short (a few bases) and long (tens of thousands of base pairs) DNA fragments. Effects of key experimental parameters, such as eluent composition and elution pressure, on separation efficiency and resolution are investigated. We also apply this technique for DNA separations of real-world genotyping samples to demonstrate its feasibility in biological applications. PCR products (without any purification) amplified from Arabidopsis plant genomic DNA crude preparations are directly injected into the nanocapillary, and PCR-amplified DNA fragments are well resolved, allowing for unambiguous identification of samples from heterozygous and homozygous individuals. Since the capillaries used to conduct the separations are uncoated, column lifetime is virtually unlimited. The only material that is consumed in these assays is the eluent, and hence the operation cost is low.New, more cost-effective DNA separation methods are being sought to meet the need for simple and inexpensive assays for research and diagnostic purposes. Traditionally, DNA separations have been performed using slab-gel electrophoresis. A shift to capillary gel electrophoresis (CGE) 1 or capillary array electrophoresis (CAE) 2-4 has resulted in improved resolution and increased throughput. Both CGE and CAE use viscous polymer solutions (e.g., entangled solutions of linear polyacrylamide) as sieving matrices for size-based DNA separations. In addition to their cost, high pressures (e.g. 1000 psi) are often needed 5 to load and replenish these matrices after each run. Frequently, a coating is required on the inner wall of the capillary in order to obtain high quality separation results.To overcome the problems associated with the viscous polymer matrices, one would wish to separate DNA in gel-free (or free) solutions. 6-12 Unfortunately, DNA separations cannot normally be achieved by electrophoresis in gel-free solutions, 13 because the electrophoretic mobilities of all DNA molecules are virtually identical. Although a long DNA molecule possesses greater negative charge than a shorter molecule does, providing stronger pull, its large size induces more friction that limits its migration. These two forces largely balance one another, resulting in a mobility that is independent of the DNA size. Credit should be given to Noolandi 6 who suggested in 1992 that DNA could be electrophoretically separated in a gelfree solution if the molecules were attached to a monodisperse perturbing entity or a "dragtag". Becaus...