Conventional electrochemical anodizing processes of metals such as aluminum typically produce planar and homogeneous nanopore structures. If hydrophobically treated, such 2D planar and interconnected pore structures typically result in lower contact angle and larger contact angle hysteresis than 3D disconnected pillar structures and, hence, exhibit inferior superhydrophobic efficiency. In this study, we demonstrate for the first time that the anodizing parameters can be engineered to design novel pillar-on-pore (POP) hybrid nanostructures directly in a simple one-step fabrication process so that superior surface superhydrophobicity can also be realized effectively from the electrochemical anodization process. On the basis of the characteristic of forming a self-ordered porous morphology in a hexagonal array, the modulation of anodizing voltage and duration enabled the formulation of the hybrid-type nanostructures having controlled pillar morphology on top of a porous layer in both mild and hard anodization modes. The hybrid nanostructures of the anodized metal oxide layer initially enhanced the surface hydrophilicity significantly (i.e., superhydrophilic). However, after a hydrophobic monolayer coating, such hybrid nanostructures then showed superior superhydrophobic nonwetting properties not attainable by the plain nanoporous surfaces produced by conventional anodization conditions. The well-regulated anodization process suggests that electrochemical anodizing can expand its usefulness and efficacy to render various metallic substrates with great superhydrophilicity or -hydrophobicity by directly realizing pillar-like structures on top of a self-ordered nanoporous array through a simple one-step fabrication procedure.

The major drawback of current passivation techniques for preventing corrosion is the lack of ability to withstand any external damages or local defects. In this study, oil‐impregnated nanoporous anodic aluminum oxide (AAO) layers are investigated to overcome such limitations and thus advance corrosion protection. By completely filling hydrophobized nanopores with oil via a solvent exchange method, a highly water‐repellent surface that prevents the penetration of corrosive media into the AAO layer and hence the corrosion of aluminum is achieved. The impregnation of oil into the hydrophobic nanoporous AAO layer enhances the corrosion resistance of an AAO layer by two and four orders of magnitude compared to that of a hydrophobic (i.e., air‐entrained) and a bare (hydrophilic) AAO, respectively. In the presence of local defects, the oil impregnated within the hydrophobic nanoporous AAO layer naturally permeates into the defects and ultimately inhibits the exposure of the aluminum surface to corrosive media. Whereas the corrosion current density of the air‐entrained hydrophobic AAO layer increases by more than 30 times after cracks, that of the oil‐impregnated AAO layer increases by no more than 4 times, showing superior anticorrosion property even after there are cracks, owing to the effective self‐healing capability.

No abstract

Nanoporous anodic aluminum oxide layers were fabricated on aluminum substrates with systematically varied pore diameters (20-80 nm) and oxide thicknesses (150-500 nm) by controlling the anodizing voltage and time and subsequent pore-widening process conditions. The porous nanostructures were then coated with a thin (only a couple of nanometers thick) Teflon film to make the surface hydrophobic and trap air in the pores. The corrosion resistance of the aluminum substrate was evaluated by a potentiodynamic polarization measurement in 3.5 wt % NaCl solution (saltwater). Results showed that the hydrophobic nanoporous anodic aluminum oxide layer significantly enhanced the corrosion resistance of the aluminum substrate compared to a hydrophilic oxide layer of the same nanostructures, to bare (nonanodized) aluminum with only a natural oxide layer on top, and to the latter coated with a thin Teflon film. The hydrophobic nanoporous anodic aluminum oxide layer with the largest pore diameter and the thickest oxide layer (i.e., the maximized air fraction) resulted in the best corrosion resistance with a corrosion inhibition efficiency of up to 99% for up to 7 days. The results demonstrate that the air impregnating the hydrophobic nanopores can effectively inhibit the penetration of corrosive media into the pores, leading to a significant improvement in corrosion resistance.

No abstract