Efficient removal of heat via thermal interface materials has become one of the most critical challenges in the development of modern microelectronic devices. However, traditional polymer composites present limited thermal conductivity even when highly loaded with highly thermally conductive fillers due to the lack of efficient heat transfer channels. In this work, vertically aligned and interconnected graphene networks are first used as the filler, which is prepared by a controlled three-step procedure: formation of graphene oxide liquid crystals, oriented freeze casting, and high-temperature annealing reduction under Ar. The obtained composite, at an ultralow graphene loading of 0.92 vol %, exhibits a high thermal conductivity (2.13 W m–1 K–1) that is equivalent to a dramatic enhancement of 1231% compared to the pure matrix. Furthermore, the composite also presents a much reduced coefficient of thermal expansion (∼37.4 ppm K–1) and increased glass transition temperature (135.4 °C). This strategy provides an insight for the design of high-performance composites with potential to be used in advanced electronic packaging.

Iron pyrite (FeS 2 ) is a promising photovoltaic absorber because of its Earth abundance, high optical extinction, and infrared band gap (E g = 0.95 eV), but its use has been hindered because of the difficulty of phase pure synthesis. Pyrite phase purity is a paramount concern, as other phases of iron sulfide have undesirable electronic properties. Here we report the synthesis of phase pure iron pyrite nanocrystals with cubic morphology and a mean dimension of 80 nm. Control over the nanocrystal shape was achieved using an unusual ligand, 1-hexadecanesulfonate. The particles were characterized via synchrotron X-ray spectroscopy, indicating an indirect band gap of 1.00 ± 0.11 eV and a valence bandwidth of nearly 1 eV. Transmission electron microscopy from early reaction stages suggests a nucleation and growth mechanism similar to solution precipitation syntheses typical of metal oxide nanocrystals, rather than the diffusion-limited growth process typical of hot-injection metal chalcogenide nanocrystal syntheses.

Kinked silicon (Si) nanowires (NWs) have many special properties that make them attractive for a number of applications, such as microfluidics devices, microelectronic devices, and biosensors. However, fabricating NWs with controlled three-dimensional (3D) geometry has been challenging. In this work, a novel method called alternating metal-assisted chemical etching is reported for the fabrication of kinked Si NWs with controlled 3D geometry. By the use of multiple etchants with carefully selected composition, one can control the number of kinks, their locations, and their angles by controlling the number of etchant alternations and the time in each etchant. The resulting number of kinks equals the number times the etchant is alternated, the length of each segment separated by kinks has a linear relationship with the etching time, and the kinking angle is related to the surface tension and viscosity of the etchants. This facile method may provide a feasible and economical way to fabricate novel silicon nanowires, nanostructures, and devices for broad applications.

Three phenylenediamine (PD) monomers, o-phenylenediamine (OPD), m-phenylenediamine (MPD), and p-phenylenediamine (PPD), were used to prepare the functionalized graphene (PD/rGO) networks. The results obtained from a series of chemical, thermal, and rheological analyses elucidated the mechanism of the covalent bonding and the existence of cross-linked graphene networks. The measured XRD patterns and molecular dynamic calculations discovered that those PPD and MPD molecules could enlarge graphene interlayer spacing to 1.41 and 1.30 nm, respectively, while OPD molecules were disorderly bonded or nonbonded to the basal planes of graphene layers, resulting in small and variable interlayer distances. The loadings of PD monomers were optimized to achieve superior supercapacitor performance. Electrochemical study showed that PPD/rGO exhibited the largest specific capacitance of 422 F/g with excellent cycling stability and low charge transfer resistance. The large variations in the capacitance values among PD/rGO networks with different PD monomers were explained by the difference in the graphene nanostructures, reversible redox transitions, and charge transfer characteristics. Particularly, density function theory calculations were adopted to compare electronic properties of the PD/rGO composites, including formation energy, electron density distribution, HOMO energy levels, and electron density of states near the Fermi level.

The fabrication of supercapacitor electrodes with high energy density and excellent cycling stability is still a great challenge. A carbon aerogel, possessing a hierarchical porous structure, high specific surface area and electrical conductivity, is an ideal backbone to support transition metal oxides and bring hope to prepare electrodes with high energy density and excellent cycling stability. Therefore, NiCoS nanotube array/carbon aerogel and NiCoO nanoneedle array/carbon aerogel hybrid supercapacitor electrode materials were synthesized by assembling Ni-Co precursor needle arrays on the surface of the channel walls of hierarchical porous carbon aerogels derived from chitosan in this study. The 1D nanostructures grow on the channel surface of the carbon aerogel vertically and tightly, contributing to the enhanced electrochemical performance with ultrahigh energy density. The energy density of NiCoS nanotube array/carbon aerogel and NiCoO nanoneedle array/carbon aerogel hybrid asymmetric supercapacitors can reach up to 55.3 Wh kg and 47.5 Wh kg at a power density of 400 W kg, respectively. These asymmetric devices also displayed excellent cycling stability with a capacitance retention of about 96.6% and 92% over 5000 cycles.