An in situ chemical synthetic approach has been designed for the fabrication of a covalently coupled hybrid consisting of graphitic carbon nitride (g-C3N4) with reduced graphene oxide (rGO) with differing g-C3N4/rGO ratio. The epoxy groups of graphene oxide (GO) undergo a nucleophilic substitution reaction with dicyandiamide (C2H4N4) to form the C2H4N4-GO composite via a covalent C-N bond, and then both the in situ polymerization of C2H4N4 and the thermal reduction of GO can be achieved at higher temperatures, forming the covalently coupled g-C3N4-rGO. FT-IR, CP-MAS NMR and XPS analyses, clearly revealed a covalent interaction between the g-C3N4 and rGO sheets. The g-C3N4-rGO exhibits an unprecedented high, stable and reversible capacity of 1525 mA h g(-1) at a current density of 100 mA g(-1) after 50 cycles. Even at a large current density of 1000 mA g(-1), a reversible capacity of 943 mA h g(-1) can still be retained. The superior electrochemical performance of g-C3N4-rGO is attributed to the specific characteristics of the unique nanostructure of g-C3N4-rGO and the concerted effects of g-C3N4 and rGO, including covalent interactions between the two moieties, the good conductivity and high special surface area of the nanocomposite, as well as the template effect of the planar amino group of g-C3N4 for the dispersed decoration of Li(+) ions.

Instead of the traditional isocyanate curing system as the binder of solid propellant, a triazole curing system has been developed by the reaction of azide group and alkynyl group due to a predominant advantage of avoiding to the interference of humidity. In this work, the propargyl-terminated polybutadiene (PTPB) was blended with glycidyl azide polymers (GAPs) to produce new composites under the catalysis of cuprous chloride at ambient temperature. The triazole-crosslinked network structure was regulated by changing the molar ratio of azide group in GAP versus alkynyl group in PTPB, and hence various crosslinked densities together with the composition changes of GAP versus PTPB cooperatively determined the mechanical properties of the resultant composites. Furthermore, the formed triazole-crosslinked network derived from the azide group in GAP and alkynyl group in PTPB resulted in the slight increase of glass transition temperatures and a-transition temperatures, and improved the miscibility between GAP and PTPB.

Depending upon the advantages of high efficiency, insensitivity to humidity and so on, the reaction of azide groups in glycidyl azide polymers (GAP) with alkynyl compounds has been used as a substitute of the urethane curing strategy to develop GAP‐based binder for solid propellant. In this work, an alkynyl compound of dimethyl 2,2‐di(prop‐2‐ynyl)malonate (DDPM) reacted with GAP to produce new crosslinked materials under the catalysis of Cu(I)Cl at ambient temperature, and showed great potential as a binder in composite propellant. As the feeding molar ratio of DDPM vs. GAP increased from 1 : 1 to 5 : 1, the crosslinking densities of as‐prepared materials gradually increased, together with simultaneous enhancement of Young's modulus and tensile strength. The breaking elongation showed the maximum value of ca. 82% when the feeding molar ratio of DDPM vs. GAP was 3 : 1. In addition, with an increase of the crosslinking densities, the glass transition temperatures of as‐prepared materials significantly increased from −43.9°C to −5.1°C while the mechanical loss peaks also gradually broadened and shifted up to high temperature, and even presented two peaks at the feeding molar ratio of DDPM vs. GAP higher than 4 : 1. It indicated that the formation of triazole‐based network resulted in structural heterogeneity in the as‐prepared materials. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40636.

No abstract

No abstract