Numerical simulations are carried out to investigate flow structures in the tip region for an axial transonic rotor, with careful comparisons with the experimental results. The calculated performance curve and two-dimensional (2D) flow structures observed at casing, such as the shock wave, the expansion wave around the leading edge, and the tip leakage flow at peak efficiency and near-stall points, are all captured by simulation results, which agree with the experimental data well. An in-depth analysis of three-dimensional flow structures reveals three features: (1) there exists an interface between the incoming main flow and the tip leakage flow, (2) in this rotor the tip leakage flows along the blade chord can be divided into at least two parts according to the blade loading distribution, and (3) each part plays a different role on the stall inception mechanism in the leakage flow dominated region. A model of three-dimensional flow structures of tip leakage flow is thus proposed accordingly. In the second half of this paper, the unsteady features of the tip leakage flows, which emerge at the operating points close to stall, are presented and validated with experiment observations. The numerical results in the rotor relative reference frame are first converted to the casing absolute reference frame before compared with the measurements in experiments. It is found that the main frequency components of simulation at absolute reference frame match well with those measured in the experiments. The mechanism of the unsteadiness and its significance to stability enhancement design are then discussed based on the details of the flow field obtained through numerical simulations.

With the help of piezoelectric high frequency pressure probes measurements are undertaken to investigate the flow during stable compressor operation close to the stability limit. Fourteen static pressure probes record the static wall pressure and ten total pressure probes record the total pressure at the rotor exit, both in the absolute frame of reference. The data is then visualised as ensemble averaged contour and spectrum plots. With the help of wall and exit pressure, the tip leakage vortex is localised. Oscillations of the tip leakage vortex are seen as well in terms of high relative standard deviation as well as in an excitation of a frequency band around 1/2 BPF. Further investigation of the frequency spectrum with the help of the pseudo-unsteady wall pressure reveal the occurrence of rotating tip leakage vortex disturbances forming a two-passage periodic vortex pattern. The presented measurements were obtained using Rotor-1 from the TU Darmstadt rotor family. With a sampling rate of 125kHz the pressure field is resolved with 23 measurements per passage (at 20.000 rpm, design speed).

The influence of circumferential grooves on the tip flow field of an axial single-stage transonic compressor rotor has been examined experimentally and numerically. The compressor stage provides a strongly increased stall margin with only small penalties in efficiency when the casing treatment is applied. Due to the complex interactions of the grooves with the rotor flow, unsteady measurement techniques have been chosen as an attempt to identify the aerodynamic effects responsible for the operating range extension. Therefore, the casing treatment has been instrumented with piezoresistive pressure sensors in the land between the grooves providing high-resolution static wall pressure measurements at different operating conditions. Data acquisition worked at a sampling rate of 125kHz, providing around 23 static pressure values per blade passage at 11 axial positions at the nominal speed of 20,000 rpm. A comparable dataset, but with 14 sensors, was obtained for the smooth casing. The results show the fluctuation of the tip leakage vortex and shock-vortex-interactions as well as the changed situation with casing treatment. Ensemble-averaged data shows tip leakage vortex trajectories. At near stall conditions with the smooth casing, the vortex hits the front part of the adjacent blade, which indicates the possibility of a spill forward of low momentum fluid into the next passage. Standard deviation values prove a high fluctuation of the pressure field over the tip gap. When the casing treatment is applied, the vortex trajectory maintains alignment along the blade’s suction side, thus preventing the onset of rotating stall. Results are presented as a back-to-back comparison of the smooth casing versus the treated casing at three operating conditions: peak efficiency at a mass flow rate of m˙pe = 16.2kg/s, near stall of the smooth casing at m˙nssc = 14.0kg/s and near stall of the treated casing at m˙ns = 12.6kg/s. Steady and unsteady numerical simulations of the rotor-only flow field have been calculated with and without grooves. These calculations aim at a broad analysis of the occurring flow phenomena at the rotor tip. Tip leakage flow behaviour and vortex trajectories are discussed in detail by summarizing the congruent findings of both numerical and experimental investigations.

Variable inlet guide vanes enhance the efficiency and stability of modern transonic compressors. The current quest for compact and highly efficient aero-engines requires for higher stage-loading and small axial gaps between adjacent blade rows, increasing interaction between blade rows and introducing further unsteadiness into the flow. Modeling these interactions is relevant to jet engine implementation. Recent advancements in numerical simulation of unsteady flow in multiple blade rows create an additional way to investigate the flow patterns formed by the unsteady interaction. In the case of transonic compressors, the experimental and numerical database is small. The current article will contribute to this database by investigating the flow downstream of an inlet guide vane and the influence this flow has on the passage in a transonic compressor. Unsteady flow phenomena are resolved by piezoresistive wall pressure tappings. Numerical and experimental data show that the interaction of blade rows influences the formation of the tip leakage vortex. Analyzing the vortex structure within the transonic compressor stage it is possible to show how the blade rows interact and how geometric modifications in the VIGV tip gap model influence simulation results.

Numerical simulations are carried out to investigate flow structures in the tip region for an axial transonic rotor, with careful comparisons with the experimental results. The calculated performance curve and 2D flow structures observed at casing, such as the shock wave, the expansion wave around the leading edge and the tip leakage flow at peak efficiency and near-stall points, are all captured by simulation results, which agree with the experimental data well. An in-depth analysis of three-dimensional flow structures reveals three features: 1) there exists an interface between the incoming main flow and the tip leakage flow, 2) in this rotor, the tip leakage flows along the blade chord can be divided into at least two parts according to the blade loading distribution, and 3) each part plays a different role on the stall inception mechanism in the leakage flow dominated region. A model of three-dimensional flow structures of tip leakage flow is thus proposed accordingly. In the second half of this paper, the unsteady features of the tip leakage flows, which emerge at the operating points close to stall, are presented and validated with experiment observations. The numerical results in the rotor relative reference frame are first converted to the casing absolute reference frame before compared with the measurements in experiments. It is found that the main frequency components of simulation at absolute reference frame match well with those measured in the experiments. The mechanism of the unsteadiness and its significance to stability enhancement design are then discussed based on the details of the flow field obtained through numerical simulations.