The electrical conductivity of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was enhanced by dipping the thin films prepared by spin coating technique in an aqueous DMSO solution. The low concentration range of DMSO in water between 0-5 vol % was studied in comparison with pure water and pure DMSO. It was found that the electrical conductivity dramatically increased as increasing the concentration of DMSO and reached the constant value of 350 S cm-1 at 2 vol % of aqueous DMSO solution. This could be explained by the conformational change of PEDOT chains from the coil structure to the linear or expanded coil structure as confirmed by Raman spectra. Further, white patches were obviously noticed on the surface of the films dipped in pure DMSO, indicating the phase separation of conductive PEDOT grains and associated PSS. The sulfur element of the dipped film surface was investigated by XPS. The XPS S2p core-level spectra displayed that the unassociated PSS was considerably removed from the surface of PEDOT:PSS films dipped in pure water and 2 vol % of aqueous DMSO solution, indicating that the presence of water in the solvents is important to prominently promote the washing effect. Finally, UV-Vis spectra revealed the improved transparency of the films probably owing to the decreased film thickness

The isothermal crystallization kinetics and morphology of the poly(lactic acid) (PLA) blends containing three different sizes of both spherical and fibrous poly(butylene terephthalate) (PBT) domains have been comparatively investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). The dynamic DSC measurement reveals that PBT domains significantly increase the degree of crystallinity of the PLA. Furthermore, the Avrami model is employed to evaluate the crystallization kinetics under isothermal conditions and it is found that PBT acts as nucleating agent, leading to a high overall crystallization rate constant k and shortened crystallization half time t 1/2 . Furthermore, the crystallization rate of PLA is promoted with the incorporation of PBT with a large specific surface area. The average Avrami index n of all samples lies within the range of 3.3 2 4.0, suggesting that morphologies of PBT do not affect the nucleation mechanism; however, the depression of equilibrium melting temperature in the blends ascribes the reductions of perfectness and size of the PLA crystallites. Besides, the nucleation of PLA crystallites around PBT fibers is probably faster than those around PBT spheres because the PBT chains oriented at the fiber surface as a result of flow-induced crystallization during melt stretching may serve as the primary nuclei for PLA chains to drastically crystallize at the fiber surface. POLYM. ENG. SCI., 56:258-268, 2016.

No abstract

We report here the morphology, thermal and tensile properties of poly(lactic acid) (PLA) blends composed of acrylonitrile butadiene rubber (NBR) with different acrylonitrile contents with/without dynamic vulcanization by dicumyl peroxide (DCP). The interfacial tension of PLA and NBR measured by contact angle measurement decreased as the acrylonitrile content of NBR decreased. Likewise, SEM images showed that the rubber particle size reduced with decreasing acrylonitrile content owing to the stronger interfacial adhesion between the PLA matrix and NBR domains. Incorporation of DCP at 1.0 phr for dynamic vulcanization led to higher crosslink density and, in turn, optimal tensile strength and tensile toughness as a result of the action of PLA-NBR copolymer as a reactive compatibilizer. The dynamic vulcanization of the blends containing low acrylonitrile NBR gave the most improved tensile properties because the free radicals from DCP decomposition preferentially attacked the allylic hydrogen atoms or double bonds of the butadiene backbone. Accordingly, more NBR macroradicals were generated and probably more PLA-NBR copolymers were produced. Moreover, further addition of DCP at 2.0 phr provided a large amount of crosslinked NBR gel, which significantly degraded the tensile properties. From the DSC results, dynamic vulcanization lowered the cold crystallization temperature, implying an improvement of cold crystallization. Finally, TGA results showed a higher degradation temperature as a function of DCP content, which suggested that thermal stability increased due to stronger interfacial adhesion as well as higher gel content.

No abstract