a b s t r a c tErosion of the leading edge of wind turbine blades by droplet impingement wear, reduces blade aerodynamic efficiency and power output. Eventually, it compromises the integrity of blade surfaces. Elastomeric coatings are currently used for erosion resistance, yet the life of such coatings cannot be predicted accurately. This review paper gives an overview of experimentally validated erosion model blocks that can be used to predict the life of the leading edge of coated wind turbine blades. From the reviewed work it is concluded that surface fatigue, as nucleating wear mechanism for erosion damage, can explain erosive wear and failure of the coatings. An engineering approach to surface fatigue, using the PalmgreneMiner rule for cumulative damage, allows for the construction of a rain erosion incubation period equation. Coating life was described as a function of the rain intensity, the droplet diameter, the fatigue properties of the coating and the severity of the conditions. It is recommended to focus coating development on reduction of the impact pressure, e.g. by developing surfaces with a low modulus of elasticity; or on enlarging the safe area by: developing coatings with adjustable compressive stresses and hardness, or coatings without defects and impurities.

No abstract

goal, a scalable process for realizing a large number of sensors over large areas with mechanical flexibility is necessary. Printed flexible and stretchable electronics envisage a drastic change in production methods, but more importantly how elec tronics are perceived and implemented. [7] In applications where thin, flexible, and stretchable properties are required, printed sensors detecting a multi tude of para meters represents an elegant solution. [8][9][10][11][12] Accurate measurement of tempera ture is of critical importance. Measuring temporal changes in temperature or spatial temperature gradients is exten sively used in industrial settings as well as for medical applications. Recently there is an increased interest in equipping complex surfaces and shapes with a large number of temperature sensors. [7,13,14] This requires a costefficient route to manufacture thermistor materials over large areas on flexi ble substrates.Thermocouples are the classical instru ment for measuring temperature, where changes in resistance of a metal is used to determine the temperature. The drawback of this method is the limited change in resistance (+0.1% °C −1 ) and the need to compensate for the cold junction temperature, making accurate measurements challenging, costly, and sensitive to artifacts. [15] Resistance temperature detectors (RTDs) represent another Surfaces which can accurately distinguish spatial and temporal changes in temperature are critical for not only flow sensors, microbolometers, process control, but also future applications like electronic skins and soft robotics. Realizing such surfaces requires the deposition of thousands of thermal sensors over large areas, a task ideally suited for printing technologies. Negative temperature coefficient (NTC) ceramics represent the industry standard in temperature sensing due to their high thermal coefficient and excellent stability. A drawback is their complex and high temperature fabrication process and high stiffness, prohibiting their monolithic integration in large area or flexible applications. As a remedy, a printable NTC composite that combines a rapid and scalable all-printed fabrication process with performances that are on par with conventional NTC ceramics is demonstrated. The composite consists of micrometer-sized manganese spinel oxide particles dispersed in a benzocyclobutene matrix. The sensor has a B coefficient of 3500 K, with a 4.0% change in resistance at 25 °C, comparable to bulk ceramics. The selected polymer binder yields a composite exhibiting less than a 1 °C change in resistance to changes in humidity. The sensor's scalability is validated by demonstration of a A4-sized temperature sensing sheet consisting of over 400 sensors.

One-dimensional metal nanowires offer great potential in printing transparent electrodes for next-generation optoelectronic devices such as flexible displays and flexible solar cells. Printing fine patterns of metal nanowires with widths <100 μm is critical for their practical use in the devices. However, the fine printing of metal nanowires onto polymer substrates remains a major challenge owing to their unintended alignment. This paper reports on a fine-printing method for transparent silver nanowires (AgNWs) electrodes miniaturized to a width of 50 μm on ultrathin (1 μm) polymer substrate, giving a high yield of >90%. In this method, the AgNW dispersion, which is swept by a glass rod, is spontaneously deposited to the hydrophilic areas patterned on a hydrophobic-coated substrate. The alignment and accumulation of AgNWs at the pattern periphery are enhanced by employing a high sweeping rate of >3.2 mm s−1, improving electrical conductivity and pattern definition. The more aligned and more accumulated AgNWs lower the sheet resistance by a factor of up to 6.8. In addition, a high pattern accuracy ≤ 3.6 μm, which is the deviation from the pattern designs, is achieved. Quantitative analyses are implemented on the nanowire alignment to understand the nanowire geometry. This fine-printing method of the AgNW electrodes will provide great opportunities for realizing flexible and high-performance optoelectronic devices.

An assay has been developed to accurately quantify the growth and release behaviour of bacterial biofilms on several test reference materials and coatings, using the marine bacterium Cobetia marina as a model organism. The assay can be used to investigate the inhibition of bacterial growth and release properties of many surfaces when compared to a reference. The method is based upon the staining of attached bacterial cells with the nucleic acid-binding, green fluorescent SYTO 13 stain. A strong linear correlation exists between the fluorescence of the bacterial suspension measured (RFU) using a plate reader and the total bacterial count measured with epifluorescence microscopy. This relationship allows the fluorescent technique to be used for the quantification of bacterial cells attached to surfaces. As the bacteria proliferate on the surface over a period of time, the relative fluorescence unit (RFU) measured using the plate reader also shows an increase with time. This was observed on all three test surfaces (glass, Epikote and Silastic T2) over a period of 4 h of bacterial growth, followed by a release assay, which was carried out by the application of hydrodynamic shear forces using a custom-made rotary device. Different fixed rotor speeds were tested, and based on the release analysis, 12 knots was used to provide standard shear force. The assay developed was then applied for assessing three different antifouling coatings of different surface roughness. The novel assay allows the rapid and sensitive enumeration of attached bacteria directly on the coated surface. This is the first plate reader assay technique that allows estimation of irreversibly attached bacterial cells directly on the coated surface without their removal from the surface or extraction of a stain into solution.