Reducing the weight and decreasing pressure losses of aviation gas turbine engines improves the thrust-to-weight ratio and improves efficiency. In ultra-compact combustors (UCC), engine length is reduced and pressure losses are decreased by merging a combustor with adjacent components using a systems engineering approach. High-pressure turbine inlet vanes can be placed in a combustor to form a UCC. In this work, experiments were performed to understand the performance and associated physics within a UCC. Experiments were performed using a combustor operating at pressures in the range of 520–1030 kPa (75–150 psia) and inlet temperature equal to 480–620 K (865 R–1120 R). The primary reaction zone is in a single trapped-vortex cavity where the equivalence ratio was varied from 0.7 to 1.8. Combustion efficiencies and NOx emissions were measured and exit temperature profiles were obtained for various air loadings, cavity equivalence ratios, and configurations with and without representative turbine inlet vanes. A combined diffuser-flameholder (CDF) was used to study the interaction of cavity and core flows. Discrete jets of air immediately above the cavity result in the highest combustion efficiencies. The air jets reinforce the vortex structure within the cavity, as confirmed through coherent structure velocimetry of high-speed images. The combustor exit temperature profile is peaked away from the cavity when a CDF is used. Testing of a CDF with vanes showed that combustion efficiencies greater than 99.5% are possible for 0.8 ≤ Φcavity ≤ 1.8. Temperature profiles at the exit of the UCC with vanes agreed within 10% of the average value. Exit-averaged emission indices of NOx ranged from 3.5 to 6.5 g/kgfuel for all test conditions. Increasing the air loading enabled greater mass flow rates of fuel with equivalent combustion efficiencies. This corresponds to increased vortex strength within the cavity due to the greater momentum of the air driver jets.

Gas-temperature measurements in the combustion zone of a high-pressure gas-turbine-combustor sector rig were made with a Fourier-domain mode-locked laser using wavelength-agile absorption-spectroscopy techniques. These measurements are among the first employing broadband high-resolution absorption spectroscopy in gas-turbineengine environments. Compared with previous measurements in reciprocating engines and shock tubes, signal contamination from thermal emission was stronger in this combustor rig; methods for managing emission during experimental planning and postprocessing are discussed. H 2 O spectra spanning 1330-1380 nm (which includes the 1 3 and 2 1 overtone bands) are presented along with a method for calculating gas temperatures from the spectra. The resulting temperatures are reported for a variety of combustor conditions. These tests show promise for simple gas-turbine sensors and potential for more detailed experiments involving tomographic reconstruction or multispecies concentration measurements. Nomenclature I = transmitted intensity I o = incident intensity k = absorption coefficient L = path length T abs = absorption-spectroscopy-inferred temperature T ave = path-integrated average temperature T flame = flame temperature = equivalence ratio

No abstract

Alternate aviation fuels for military or commercial use are required to satisfy MIL-DTL-83133F or ASTM D 7566 standards, respectively, and are classified as "drop-in" fuel replacements. To satisfy legacy issues, blends to 50% alternate fuel with petroleum fuels are acceptable. Adherence to alternate fuels and fuel blends requires "smart fueling systems" or advanced fuel-flexible systems, including combustors and engines, without significant sacrifice in performance or emissions requirements. This paper provides preliminary performance and emissions and particulates combustor sector data. The data are for nominal inlet conditions at 225 psia and 800• F (1.551 MPa and 700 K), for synthetic-paraffinic-kerosene-(SPK-) type (Fisher-Tropsch (FT)) fuel and blends with JP-8+100 relative to JP-8+100 as baseline fueling. Assessments are made of the change in combustor efficiency, wall temperatures, emissions, and luminosity with SPK of 0%, 50%, and 100% fueling composition at 3% combustor pressure drop. The performance results (Part A) indicate no quantifiable differences in combustor efficiency, a general trend to lower liner and higher core flow temperatures with increased FT fuel blends. In general, emissions data (Part B) show little differences, but, with percent increase in FT-SPK-type fueling, particulate emissions and wall temperatures are less than with baseline JP-8. High-speed photography.

Reducing the weight and decreasing pressure losses of aviation gas turbine engines improves the thrust-to-weight ratio and improves efficiency. In ultra-compact combustors (UCCs), engine length is reduced and pressure losses are decreased by merging a combustor with adjacent components using a systems engineering approach. High-pressure turbine inlet vanes can be placed in a combustor to form a UCC. Eliminating the compressor outlet guide vanes (OGVs) and maintaining swirl through the diffuser can result in further reduction in engine length and weight. Cycle analysis indicates that a 2.4% improvement in engine weight and a 0.8% increase in thrust-specific fuel consumption are possible when a UCC is used. Experiments and analysis were performed in an effort to understand key physical and chemical processes within a trapped-vortex UCC. Experiments were performed using a combustor operating at pressures in the range of 520–1030 kPa (75–150 psi) and inlet temperature of 480–620 K (865–1120 °R). The primary reaction zone is in a single trapped-vortex cavity where the equivalence ratio was varied from 0.7 to 1.8. Combustion efficiencies and NOx emissions were measured and exit temperature profiles obtained, for various air loadings, cavity equivalence ratios, and configurations with and without turbine inlet vanes. A combined diffuser-flameholder (CDF) was used in configurations without vanes to study the interaction of cavity and core flows. Higher combustion efficiency was achieved when the forward-to-aft momentum ratios of the air jets in the cavity were near unity or higher. Discrete jets of air immediately above the cavity result in the highest combustion efficiency. The air jets reinforce the vortex structure within the cavity, as confirmed through coherent structure velocimetry of high-speed images. A more uniform temperature profile was observed at the combustor exit when a CDF is used instead of vanes. This is the result of increased mass transport along the face of the flame holder. Emission indices of NOx were between 3.5 and 6.5 g/kgfuel for all test conditions. Ultra-compact combustors (with a single cavity) can be run with higher air loadings than those employed in previous testing with a trapped-vortex combustor (two cavities) with similar combustion efficiencies being maintained. The results of this study suggest that the length of combustors and adjacent components can be reduced by employing a systems level approach.