Shale gas reservoirs are tight reservoirs with ultralow porosity and ultralow permeability, and their matrix pores are mostly nanoscale. In addition, matrix particles and organic pore surfaces adsorb shale gas. These problems cause the production per well of shale gas to be lower than that of conventional natural gas. The use of hydraulic fracturing technology to exploit shale gas can achieve a good production increase effect. However, using this technology has some limitations caused by technical characteristics and geological conditions. Therefore, new technologies for shale gas exploitation need to be explored. In this study, we propose a method to improve the flow characteristics of shale gas by using ultrasonic waves to increase shale gas production and perform experimental tests to research the actual effect of this method. The lithology, mineral composition, pore structure, specific surface area, and pore size distribution of shale samples are tested. Then, the attenuation characteristics of ultrasonic waves propagating in shale are analyzed. Finally, the effect of ultrasonic waves on the adsorption, desorption, and seepage of shale gas is explored. Results show that the Langmuir adsorption isotherm can describe the adsorption characteristics of shale gas under the action of ultrasonic waves. The gas adsorption constant decreases with increasing ultrasonic wave power. The ultrasonic waves accelerate the gas desorption rate, significantly increase the desorption volume, and prolong the time taken to reach desorption equilibrium. They also increase the permeability of shale gas, and the growth is proportional to the power of the ultrasonic waves. These results indicate that the permeability of shale gas has a power function relationship with the effective stress under ultrasonic waves.

The matrix pores of a coalbed methane (CBM) reservoir are mostly nanoscale pores, with tiny pore throats and poor connectivity, which belong to the category of low–permeability gas reservoirs. The matrix particles and organic pore surfaces adsorb a large amount of CBM. These problems are the main reasons that limit the increase in CBM production. At present, the primary measure to increase CBM production is hydraulic fracturing. However, due to the technical characteristics and geological conditions of CBM reservoirs, applying this technology to CBM exploitation still has some key issues that need to be resolved. Therefore, it is essential to develop a new technology that can effectively increase the production of CBM. This paper proposed a method that uses ultrasonic waves to improve the seepage characteristics of CBM reservoir and theoretically verifies the feasibility of this idea using numerical simulation. In this paper, we firstly coupled the temperature, pressure, and seepage parameters of the CBM reservoir and built a CBM seepage model under the action of ultrasonic waves. Secondly, by comparing the numerical simulation results with the experiment, we verified the accuracy of the model. Finally, on the basis of the mathematical model, we simulated the change characteristics of pore pressure, reservoir temperature, permeability, and porosity under the action of ultrasonic waves. Research results show that under the action of ultrasonic waves, the pressure-drop funnel of CBM reservoir becomes more apparent. The boundary affected by the pressure drop also increases. With the increase of the action time of ultrasonic waves, the temperature of CBM reservoir also increases, and the action distance is about 4 m. With decreased pore pressure, the permeability and porosity of CBM reservoir significantly increase under the action of ultrasonic waves. With increased ultrasonic power, its effect on reservoir permeability and porosity becomes more significant.

In the actual exploitation process of coalbed methane (CBM), as the fluid in the wellbore continues to circulate, the surrounding rock of the CBM well will continuously exchange heat with the fluid in the wellbore, resulting in continuous changes in the temperature of the surrounding rock itself. Linfen, Shanxi is the main exploitation area for CBM in China. This paper aims further to improve the exploitation efficiency of CBM in this area and conducts experimental research on the change characteristics of coal-rock mechanical properties under varying temperature conditions. The experimental results show that under constant pressure conditions, the higher the temperature, the lower the stress value when the coal-rock breaks. In the process of reaching peak strength, the higher the temperature, the higher the proportion of coal-rock plastic deformation in its entire deformation stage. The compressive strength, elastic modulus, and main crack length of coal-rock will decrease with temperature. The Poisson's ratio and primary fracture angle will increase with the increase of experimental temperature.

The borehole stability of the coalbed methane (CBM) well has always been vital in deep CBM exploration and development. The borehole instability of the deep CBM well is due to many complicated reasons. The change in the surrounding rock temperature is an important and easily overlooked factor among many reasons. In this research, we used methods that include experiment and numerical simulation to study the characteristic law of the borehole deformation induced by the changes in the surrounding rock temperature of deep CBM well. The experimental results of the stress–strain curves of five sets of experiments show that when the experimental temperature rises from 40 °C to 100 °C, the average stress when coal samples are broken gradually decreases from 81.09 MPa to 72.71 MPa. The proportion of plastic deformation in the entire deformation stage gradually increases from 7.8% to 25.7%. Moreover, the characteristics that some key mechanical parameters of coal samples change with the experimental temperature are fitted, and results show that as the experimental temperature rises from 40 °C to 100 °C, the compressive strength, elastic modulus, and main crack length of coal samples show a gradually decreasing trend. By contrast, the Pois-son's ratio and primary fracture angle show a gradually increasing trend. Moreover, the relativity of the linear equations obtained by fitting is all close to 1, which can accurately reflect the corresponding change trend. Numerical simulation results show that a high temperature of the surrounding rock of the deep CBM well results in a high range of stress concentration on the coal seam borehole and high deformation.

In empty well killing, in order to save the time and cost of killing the well, the dynamic replacement method is often used to kill the well. The main problem of the dynamic replacement method for killing wells is how to avoid terrible working conditions caused by flooding, such as gas carrying fluid, killing fluid being brought to the wellhead. Based on the principle of flooding formation and the basic tenets of flooding correlation experiment and dynamic replacement method, this paper incorporates the kill fluid viscosity, surface tension, droplet diameter, inclination angle, drill pipe joint outer diameter, and drill pipe eccentricity into the calculation range and establishes a new mathematical model suitable for dynamic replacement kill. Based on the calculation results, the influencing factors of flooding are analyzed, and the following conclusions are drawn: the increase of dynamic viscosity, gas density in the well, casing pressure, well angle, the outside diameter of drill pipe, the outer diameter of drill pipe joint, and eccentricity of drill pipe can promote the occurrence of flooding; The increase of surface tension, well-killing fluid density, and casing inner diameter have an obstacle to flooding.