A number of navigation systems used for total knee replacement surgery currently require the insertion of a distal femoral reference sensor pin, which is placed anterior to posterior just superior to the level of the knee joint. There is potential for the posterior neurovascular bundle to be damaged during the insertion of this sensor device. The aim of this cadaveric study was to identify the structures at risk during insertion of the distal femoral sensor, and determine whether a safe zone for insertion could be identified. Sixteen cadaveric lower limbs (8 pairs) were studied. In each knee Steinman pins were passed from anterior to posterior, 5 cm proximal to the level of the femoral articular cartilage, directly AP and angled at 30 degrees passing medially or laterally. All pins that were passed directly from anterior to posterior and from lateral to medial passed within 5 mm of a major neurovascular structure, while 62.5% of pins passing from medial to lateral passed within 5 mm of a major neurovascular structure. The popliteal vessels and the sciatic nerve are at risk of injury from a navigation pin or drill placed in the distal femur during knee navigation. Caution should be exercised in passing these pins and alternate methods of fixing femoral sensors should be considered.

A number of navigation systems used for total knee replacement surgery currently require the insertion of a distal femoral reference sensor pin, which is placed anterior to posterior just superior to the level of the knee joint. There is potential for the posterior neurovascular bundle to be damaged during the insertion of this sensor device. The aim of this cadaveric study was to identify the structures at risk during insertion of the distal femoral sensor, and determine whether a safe zone for insertion could be identified. Sixteen cadaveric lower limbs (8 pairs) were studied. In each knee Steinman pins were passed from anterior to posterior, 5 cm proximal to the level of the femoral articular cartilage, directly AP and angled at 30 degrees passing medially or laterally. All pins that were passed directly from anterior to posterior and from lateral to medial passed within 5 mm of a major neurovascular structure, while 62.5% of pins passing from medial to lateral passed within 5 mm of a major neurovascular structure. The popliteal vessels and the sciatic nerve are at risk of injury from a navigation pin or drill placed in the distal femur during knee navigation. Caution should be exercised in passing these pins and alternate methods of fixing femoral sensors should be considered.

The primary aim of computer-assisted knee arthroplasty is to improve the alignment of the implanted prostheses. Accurate component alignment is dependent on the establishment of accurate anatomical reference points. Current techniques for establishing the center of the ankle joint, especially in the coronal plane, rely solely on clinical judgment in relation to the position of the center of the ankle joint. The aim of this study was to determine if an algorithm could be developed, based on establishing the most prominent points on the medial and lateral malleoli on 3D CT scans, to accurately and reproducibly establish the position of the center of the ankle joint. To determine this, images of 20 ankles were obtained and axial, coronal, and sagittal 2D reconstructions were manipulated on a workstation. Two observers independently performed relevant measurements and calculations. The calculated data was found to be reproducible with a very small standard deviation in each plane. This algorithm is able to provide accurate measurements of the ankle joint in knee navigation surgery. Caution must be exercised in anatomically abnormal ankles, as the calculations of the ankle center were found to be significantly different.

The primary aim of computer-assisted knee arthroplasty is to improve the alignment of the implanted prostheses. Accurate component alignment is dependent on the establishment of accurate anatomical reference points. Current techniques for establishing the center of the ankle joint, especially in the coronal plane, rely solely on clinical judgment in relation to the position of the center of the ankle joint. The aim of this study was to determine if an algorithm could be developed, based on establishing the most prominent points on the medial and lateral malleoli on 3D CT scans, to accurately and reproducibly establish the position of the center of the ankle joint. To determine this, images of 20 ankles were obtained and axial, coronal, and sagittal 2D reconstructions were manipulated on a workstation. Two observers independently performed relevant measurements and calculations. The calculated data was found to be reproducible with a very small standard deviation in each plane. This algorithm is able to provide accurate measurements of the ankle joint in knee navigation surgery. Caution must be exercised in anatomically abnormal ankles, as the calculations of the ankle center were found to be significantly different.