The objective of this research was to find the best combination of factor levels that minimized the surface roughness of prototyped samples from Fused Deposition Modeling (FDM). Two sets of experiments were conducted for that purpose; a two-level three-factor full factorial experiment and a three-level two-factor full factorial experiment. The parameters chosen for this research were model temperature, layer thickness and part fill style. The results obtained from both experiments were compared and analyzed in order to determine the best combination of factors that minimized the surface roughness of the specimens. The significant factors, their interactions and the optimum setting are presented in this paper

The Sn–Ag–Cu (SAC) solders with low Ag or Cu content have been identified as promising candidates to replace the traditional Sn–Pb solder. In this study, an extensive discussion was presented on two major area of mechanical properties and microstructural investigation of SAC305 and SAC405. In this chapter, we study the composition, mechanical properties of SAC solder alloys and microstructure were examined by optical microscope and SEM and mechanical properties such as tensile tests, hardness test and density test of the lead solder alloys were explored. SAC305 and SAC405 alloys with different Ag content and constant Cu content under investigation and compare the value of SAC305 and SAC405. From this investigation, it was reported that tensile strength is increased, with an increase of Ag content and hardness and density were also increases in the same manner.

The Lead-free solders (SAC) with low Ag content have been identified as crucial solder to replace the traditional Sn-Pb solder. The main discussion was presented in two major area of microstructural investigation and mechanical properties of SAC305 and SAC405. Composition and microstructure of SAC solder alloys were investigated by an optical microscope and SEM (Scanning Electron Microscopy). Mechanical properties such as tensile tests and hardness test of the lead-free solder alloys have been tested in this research. Different Ag content and constant Cu content of lead-free solder has been considered in this investigation and compare the mechanical properties of SAC305 and SAC405 solders. From this investigation, tensile strength and hardness have been increased with increased of Ag content.

Two types of electrodynamic forming process have been developed: electromagnetic and electrohydraulic forming. In the case of electromagnetic forming, the energy stored in a capacitor bank is discharged through a coil, which means that the electrical interaction between the coil and the plate or a tubular part to be formed results in deformation of the workpiece. However, in the case of electrohydraulic forming, the capacitor bank is discharged through a spark gap or filament wire; the deformation of the workpiece is due to the shockwaves, generated by the discharge process in a transmitting medium. In both processes, a large amount of energy is released in extremely short time, therefore these processes are considered to be high energy rate forming processes. These high energy rates, result in increasing the formability of the materials in many cases, and obtain significant deformations also for some materials that normally do not behave plastically. The utilization of the energy stored in the capacitor bank is significantly better in the case of electrohydraulic forming, because the released energy is converted directly to pressure waves, results in forming of higher strength materials. Both metallic and non-metallic materials can be formed by the technologies of electromagnetic and electrohydraulic technologies. In the present paper some aspects and applications of these high energy rate methods are briefly outlined mainly focusing on the automotive industry, involving expansion or compression forming of tubular parts, joining and assembly operations.

Electromagnetic forming is a high speed forming process, wherein the forming pressure is created by high energy density electromagnetic pulse. Besides direct shaping there are other application areas as well, so electromagnetic plastic forming is a potential field of creating joints between tube and rod-like components. Connecting components of dissimilar materials is an increasing demand in the manufacturing process of structures in the automotive industry. The application of new technologies, such as electrodynamic, especially electromagnetic forming, is a possible method to satisfy these demands. The article summarizes the most important fundamentals of electromagnetic forming; in particular, tube-rod joints, the main types of such joints; interference-fit and form-fit joints are described. Experiments, which were carried out producing tube-rod joints with electromagnetic forming, are also introduced. A new type of form-fit joints for tube-rod connections has been developed, which can withstand not only tensile loads but also torsion. Experiments and mechanical tests have proved the applicability of this kind of joints.