The cyclic variance of PM10 mass concentration in the urban area in the South-East of Romania has been analysed in the article. SE of Romania is considered to be a territory which has medium level of pollution for a period of last ten years, from 2009 to 2018. The spatial dispersion of PM10 concentration was obtained using the METI-LIS soft wear for each season. The objective of dispersion models is to evaluate how pollutant concentration is spread out taking into account the diffusion. The average measurements of PM10 and meteorological parameters as inputs has been used. An evident seasonal change of PM10 concentrations is observed in the article. In order to establish national measures for the improvement of the atmospheric pollution control it was analysed the mechanism of atmospheric pollution. It was observed that the air quality was overall better in spring and in summer in comparison to the other two periods. With regard to the seasonal variation characteristics of PM10 significant differences for the air quality registered in different months in the researched region were observed. The impact of air temperature on atmospheric pollution was insignificant in spring and autumn; moreover, precipitation was defined as an important influence factor upon the atmospheric pollution. The impact of precipitation on the possibility of atmospheric pollution was obviously different in the four seasons. The research results indicate the meteorological parameters that influence the air pollution become active during the cold seasonal days. It was shown that relative humidity and wind speed are the meteorological parameters that impact the PM10. It was found out that the probability of atmospheric pollution decreased with the increase of air temperature in summer. The research results also testify that the air pollution mapping could be enhanced using atmospheric dispersion models and in-situ measurements.

The article focuses on the evaluation of PM2.5 and PM10, pollutants resulting from the metallurgical industry in Romania. The analysed period is 2008-2018 and the dataset was provided by the National Institute of Statistics. The purpose of this paper is to examine the impact of final energy consumption in the metallurgical industry on PM10 and PM2.5 emissions. We included in the study three fundamental factors: the final energy consumption in the metallurgical industry and the particulate matter (PM10 and PM2.5). The average of PM10 for reference period is 4026 Tone (Mg) while for the PM2.5 the average is 3645 Tone (Mg). The trend of final energy consumption in the metallurgical industry is identical to the trend of PM2.5 and PM10, which indicates that this factor has a major influence on the amount of PM2.5 and PM10 emissions. PM2.5 and PM10 emission factors represent primary emissions from the metallurgical industry activities and do not consider the formation of secondary aerosol from chemical reaction in the environment afterwards the discharge.

The analysis of several criteria for influent and effluent of urban sewer water treatment plant in south and south east of Romania, has a crucial role in establishing the correlations between these factors, and furthermore to assess the efficiency of the treatment system. Increasing urbanization degree and its complexity has made studies of the pollution impact appraisal to be a necessity. The mean values of the parameters measured from the wastewater plant influent like temperature, pH, suspended solids, chemical oxygen demand and biological oxygen demand vary from 17.13 � 0.23�C, 7.68 � 0.04, 234.72 � 1.55 mg/L, 396.42 � 0.76 mg/L, and 190.29 � 15.23 mg/L, respectively. The values of the above-mentioned quality indicators after the water treatment are 17.11 � 0.14�C, 7.56 � 0.03, 22.6 � 1.02 mg/L, 62.95 � 0.16 mg/L and 20.49 � 9.06 mg/L. Correlation study intended to define the feasible dependence among the evaluated parameters indicated that there were positive and negative correlations between the influent and effluent. The study conclusions point out the certitude that exist major optimizations in wastewater property after treatment processing.

The purpose of this article is to analyse the level of pollution of the installations related to the steel foundry operated by S.C. PROMEX S.A. Brăila, activity carried out on site and facilities put into operation, to assess the impact of these activities on the quality of environmental factors, potential risk and measures taken to prevent and reduce pollution. The determination of carbon monoxide (mg/m 3) and Suspended particles (mg/m 3) was done during 2016-2019.