Natural fiber-reinforced thermoplastic composites can be an alternative to mineral fiber-based composites, especially when economic and environment concerns are included under the material selection criteria. In recent years, the literature has shown how lignocellulosic fiber-reinforced composites can be used for a variety of applications. Nonetheless, the impact strength and the water uptake behavior of such materials have been seen as drawbacks. In this work, the impact strength and the water uptake of composites made of polypropylene reinforced with fibers from recycled newspaper have been researched. The results show how the impact strength decreases with the percentage of reinforcement in a similar manner to that of glass fiber-reinforced polypropylene composites as a result of adding a fragile phase to the material. It was found that the water uptake increased with the increasing percentages of lignocellulosic fibers due to the hydrophilic nature of such reinforcements. The diffusion behavior was found to be Fickian. A maleic anhydride was added as a coupling agent in order to increase the strength of the interface between the matrix and the reinforcements. It was found that the presence of such a coupling agent increased the impact strength of the composites and decreased the water uptake. Impact strengths of 21.3 kJ/m 3 were obtained for a coupled composite with 30 wt % reinforcement contents, which is a value higher than that obtained for glass fiber-based materials. The obtained composites reinforced with recycled fibers showed competitive impact strength and water uptake behaviors in comparison with materials reinforced with raw lignocellulosic fibers. The article increases the knowledge on newspaper fiber-reinforced polyolefin composite properties, showing the competitiveness of waste-based materials.In the case of the ONPF composites, the mixer was operated at 80 rpm and 180 °C . The mixing lasted 178 10 min. The coupled GF-reinforced composites were mixed at 20 rpm due to the fragility of such 179 reinforcements. All the resulting melts were pelletized in a knife mill. Prior to its mold injection, the 180 pellets were dried during 1 h in a stove at 80 °C . 181Standard rectangular specimens measuring 62 × 13 mm, with a thickness of 3.2 mm, in 182 agreement with ASTM D638 [44] were mold injected. The injection molding machine was a Meteor 183 40 by Mateu&Solé (Barcelona, Spain). The machine has three heating areas, which were operated at 184 175, 175, and 190 °C , of which the last was the injection nozzle. The first and second pressures were 185 120 and 37.5 kgf/cm 2 , respectively. At least seven valid specimens for any of the composite 186 formulations were mold injected. Five were devoted to the impact test and two were devoted to water 187 uptake analysis. 188 2.4. Specimens Testing 189 Impact strength was carried out in agreement with the ISO 179-1:2010 standard [45]. Un-notched 190 specimens were placed in a Charpy test equipment Instron Ceast 5.5 Resil by Ceast S.p.a. (Pianezza,

The transmission of information has gone through various stages of evolution throughout its history. A stage before that of the electric telegraph was the so-called aerial/optical telegraph. It was developed towards the end of the 18 th century and was in service until the middle of the 19 th century. Chappe's system was widely used in France, and was the first to be in consistent use. However, a new and technologically superior system was developed soon afterwards which superseded it. Its inventor was Agustín de Betancourt, considered by some authors one of the founders of the Theory of Machines and Mechanisms, who, together with the distinguished clockmaker Breguet, presented it to the French Authorities in the turbulent decade of the 1790s.This article presents a historical review of this telegraph and analyses its technical characteristics. It presents analytically, numerically and graphically some of the statements made about the telegraph, and corrects other subsequent observations. Lastly, a detailed reconstruction of the telegraph is made using different advanced CAD techniques, which provide an accurate static and dynamic view of each of its parts.

Stiffness of material is a key parameter that allows the use of material for structural or semi-structural purposes. Besides, lightweight materials are increasingly calling the attention of the industry. Environmental impact is also increasing in its importance. Bio-based materials produced from renewable sources can be good candidates for structural purposes combining lightweight and low environmental impact. Nonetheless, similar mechanical properties of commodities have to be reached with such materials. In this work, composite materials from corn stover fibers as a bio-polyethylene reinforcement were produced and tested. The effect of coupling agents to improve the fiber–matrix interface has been evaluated. It has been found that coupling agent content influenced the stiffness of the materials, increasing the Young’s modulus and the material processability. The best performance was achieved for a 6% of coupling agent, corresponding to 4.61 GPa for 50 w/w% of corn stover fibers. Micromechanics showed the impact of the semi-random orientation of the fibers and the lesser impact of its morphology. It was possible to determine a triangular packing of the composites as a hypothesis for future research.

No abstract

This article presents evidence of the convenience of implementing the geometric places of the plane into commercial computer-aided design (CAD) software as auxiliary tools in the computer-aided sketching process. Additionally, the research considers the possibility of adding several intuitive spatial geometric places to improve the efficiency of the three-dimensional geometric design. For demonstrative purposes, four examples are presented. A two-dimensional figure positioned on the flat face of an object shows the significant improvement over tools currently available in commercial CAD software, both vector and parametric: it is more intuitive and does not require the designer to execute as many operations. Two more complex three-dimensional examples are presented to show how the use of spatial geometric places, implemented as CAD software functions, would be an effective and highly intuitive tool. Using these functions produces auxiliary curved surfaces with points whose notable features are a significant innovation. A final example provided solves a geometric place problem using own software designed for this purpose. The proposal to incorporate geometric places into CAD software would lead to a significant improvement in the field of computational geometry. Consequently, the incorporation of geometric places into CAD software could increase technical-design productivity by eliminating some intermediate operations, such as symmetry, among others, and improving the geometry training of less skilled users.