Radical-scavenging activity of isorhamnetin (1) and its diglycosides, named isorhamnetin-3,5’-O-β-D-diglucoside (2) and isorhamnetin-3,7-O-β-D-diglucoside (3) extracted from Anoectochilus roxburghii, has been studied through three main antioxidant pathways: hydrogen atom transfer (HAT), single electron transfer followed by proton transfer, and sequential proton loss electron transfer (SPLET). All thermodynamic parameters related to these radical-scavenging mechanisms were computed at the B3LYP/6-311G(d,p) level of theory both in the gas phase and in solution. The results suggest that HAT is the predominant mechanism in the gas phase, while SPLET is supported in an aqueous environment. In addition, the stability of radicals has also been explored by electron spin density and intramolecular hydrogen bonding. The potential energy profiles and kinetic calculations for the reactions between the selected compounds and the CH3OO• radical were calculated at 298.15 K. Among all investigated, compound 2 has the highest antioxidant activity with the lowest Gibbs free energy (−4.05 kcal/mol) and the highest hydrogen atom transfer rate constant (3.61 × 105 M–1 s–1). Substitution of the OH and OMe groups by two glucoses at the 3 and 5′ sites of isorhamnetin has a significant impact on its antioxidant activity.

Understanding the physicochemical properties of corrosion inhibitors and their chemical interactions with metal surfaces is crucial to the design of improved (i.e., more efficient) corrosion inhibitors. In this work, the physicochemical properties of six thiophene-based corrosion inhibitors (2-acetylthiophene (AT), 2-formylthiophene (FT), thiophene (Th), 2-methyl-3-thiophenthiol (MTT), 2-pentylthiophene (PT), and 2-thenylthiol (TT)) were systematically studied by performing ab initio calculations at the MP2(full)/6-31G(2df,p) level of theory. Adsorption of the inhibitors on an iron surface was also modeled by investigating the interactions of these molecules with a tetrahedral Fe cluster using the B3LYP method and the 6-311G(d,p) basis set or the LanL2DZ basis set. The calculated results indicate that the nature of the substituent group present has a significant impact on the geometric and electronic structures of the thiophene-based molecules. The presence of an electron-donating group causes the electron density in the thiophene ring to increase, while the presence of an electron-withdrawing group has the opposite effect. Accordingly, the examined molecules were ranked in order of corrosion inhibition efficiency as follows: FT ≈ AT < Th < PT < TT < MTT. The calculated binding energies demonstrated that the π-1Fe and π-3Fe interaction configurations dominated over the S-1Fe configuration for all the compounds. Natural bond orbital analysis revealed that all of the thiophene-based compounds donate electrons from the π and σ orbitals of high-electron-density regions such as C2-S1-C5 and C3-C4 or from two lone pairs on S1 to the Fe cluster. Although electron donation from the thiophene-based compounds is always the dominant electron transfer process during adsorption, the backdonation of electrons from the 3d orbital of iron to σ*-antibonding orbitals of the thiophene compounds is also observed, especially in the case of π-3Fe parallel adsorption. Graphical abstract Optimized geometry, HOMO and LUMO for the π-3Fe interaction configuration of 2-pentylthiophene and Fe cluster.

1,3-Diphenyl-2-thiourea (DPTU) and 1-phenyl-3-(2-pyridyl)-2-thiourea (PPTU) were selected as the researched subject for investigating the effect of heteroatoms on the low carbon steel corrosion inhibition ability. Results from the potentiodynamic polarization measurements (PPM) indicate that the addition of a nitrogen atom in the benzene ring increases the corrosion inhibition efficiency of PPTU (97.2%), being higher than that of DPTU (93.1%) at the same condition of 2.0 × 10 –4 M at 30 °C. The Nyquist diagrams show that increasing the concentrations of both DPTU and PPTU will enhance the charge-transfer resistance and reduce the double-layer capacitance. The obtained data based on PPM and electrochemical impedance spectroscopy methods are in accordance to the analysis based on the scanning electrochemical microscopy images. Besides, results from quantum chemical calculations prove that the heteroatoms in the inhibitor molecules are the adsorption centers, and the benzene rings increase the electrostatic interaction between the inhibitor molecules and the steel surface. Results from Monte Carlo and molecular dynamics simulation have clarified the adsorption mechanism of DPTU and PPTU on the steel surface. Adsorption energies confirm that PPTU displays the higher inhibition ability as compared with DPTU.

The corrosion inhibition of mild carbon steels in an acidic environment by using ampicillin (AMP) has been evaluated based on experimental and quantum chemistry techniques. The experimental results indicate that the inhibition efficiency goes up at higher AMP concentration. The highest inhibition efficiency reaches 84.9% for polarization measurement and 90.1% for electrochemical impedance spectroscopy with the inhibitor of concentration 100 ppm at 298 K. The surface characteristics (SEM) also reconfirm the steel corrosion inhibition ability of AMP. Some important chemical factors such as EHOMO (highest occupied molecular orbital energy), ELUMO (lowest unoccupied molecular orbital energy), ΔEL−H (energy gap), and Fukui functions were calculated based on the optimized configuration of AMP at the theoretical level of B3LYP/6-31+G(d,p). Moreover, Monte Carlo and molecular dynamics simulations were used to analyze the absorption behavior of inhibitor on the surface of Fe(110), which supplies the mechanism of inhibition corrosion processes. The obtained results showed that AMP is considered to be a potential corrosion inhibitor for mild steel in 1M HCl medium. Moreover, the protonated state of AMP plays an important role in the protection of Fe surface against the corrosive process.