Introduction: bonded fixed retainers are often used to stabilize the results obtained with the orthodontic treatment. It is important that they do not prejudice dental health, as they will be used for a long period. Objective: The purpose of the present study was to compare periodontal indexes between two types of bonded fixed retainers, conventional 3 x 3 plain retainer (0.8-mm orthodontic wire, bonded to the canines only) and a manufactured braided retainer (0.2 x 0.7-mm stainless steel wire, bonded to all anterior teeth) after use. Methods: a test group of 15 volunteers (aged from 18 to 25 years) used both the conventional retainer and braided retainer for six months. A randomized longitudinal study design, with a two week washout interval, was applied. The dental plaque index, gingival index and dental calculus index were evaluated. Furthermore, the calculus accumulated along the retainer wire was measured and all patients answered a questionnaire about the use, acceptance and comfort of both types of retainers. Results: the scores for plaque and gingival indexes were higher for the braided retainer (p< 0.05) on the lingual and proximal surfaces. The same occurred with the calculus index on the lingual surfaces (p< 0.05). The calculus index along wire was higher for the braided retainer (p< 0.05). All patients preferred the conventional retainer, and said that it was also more comfortable to use. Conclusion: it was concluded that the conventional retainer showed better periodontal indexes than the braided type.

Background . This in vitro study aimed to evaluate biofilm accumulation on and deactivation force of orthodontic nickeltitanium (NiTi) archwires before and after exposure to an oral medium. Methods. Four commercial brands of orthodontic NiTi 0.016" archwires were examined before and after exposure to the oral medium for 4 weeks. Six archwire segments, 30 mm in length, from each manufacturer were tested in a device with four selfligating brackets, channel 0.022", adapted to a universal test machine to evaluate the deactivation force between 0.5 and 3 mm of deflection. The presence of biofilm on the archwire surfaces was evaluated by scanning electron microscopy, before and after exposure to the oral medium. The Wilcoxon and kappa tests were applied to the biofilm scores, three-way ANOVA for repeated measures (Bonferroni post-test), and linear regression between biofilm and deactivation force. Results. The exposure to the oral medium promoted moderate to severe presence of debris on the archwire surfaces and caused a reduction in deactivation force for the Ormco and GAC brands, while maintaining them with adequate force levels. The MORELLI and ORTHOMETRIC archwires underwent no significant reduction in deactivation force; moreover, these maintained elevated levels of force after exposure to the oral medium. The Spearman test indicated a low correlation between biofilm accumulation and deflection force for the Morelli (R2=0.132 and P=0.683) and Orthometric (R2=0.308 and P=0.330) brands. On the other hand, the GAC (R=0.767 and P=0.004) and ORMCO (R=0.725 and P=0.008) brands exhibited statistically significant correlation between these variables. Conclusion. Exposure to the oral medium for one month might give rise to significant changes in the dissipation of forces of orthodontic NiTi archwires, resulting from biofilm accumulation.

Background . This study evaluated the phase transformation of NiTi orthodontic wires and forces they release on deactivation. Methods. The structural phase transformations of the following five thermo-activated nickel-titanium (NiTi) wires were evaluated using differential scanning calorimetry (DSC): Flexy Thermal Sentalloy® (GAC International), NiTi (35ºC) (Eurodonto), Thermo-Plus® (Morelli), FlexyNiTi® Flexy Thermal (35ºC) (Orthometric) and Damon® CuNiTi (35ºC) (ORMCO Corp.). The wires had a cross-section of 0.40 mm (0.016"). In addition, the forces they released were investigated using the three-point bending test. Five arches of each wire were tested using DSC (-20/80ºC at 10ºC/min), and six arches from each wire were sectioned for bending tests. The data were analyzed with ANOVA and post hoc Tukey tests. Pearson’s correlation test was performed between the results yielded by the DSC tests and those by three-point analyses (P=0.05). Results. The DSC analysis showed differences between the NiTi alloys from all the manufacturers, with no differences between the lots of the same brand. ORMCO and Orthometric wires exhibited similar TTR values in cooling (P=0.49), and statistically similar TTR values in heating (P=0.056). The three-point bending test showed different patterns in releasing forces. A correlation was found between the DSC analysis and the three-point bending test results. Conclusion. The higher the temperature transformation was, the larger was the variation of force. All the wires presented higher forces at 3-mm deflection from 155 (±12.3) to 168.1 (±8) cN. The DSC analysis and the three-point bending test showed differences between the NiTi alloys from all the manufacturers.

No abstract