Medicine is a rapidly-evolving discipline, with progress picking up pace with each passing decade. This constant evolution results in the introduction of new tools and methods, which in turn occasionally leads to paradigm shifts across the affected medical fields. The following review attempts to showcase how 3D printing has begun to reshape and improve processes across various medical specialties and where it has the potential to make a significant impact. The current state-of-the-art, as well as real-life clinical applications of 3D printing, are reflected in the perspectives of specialists practicing in the selected disciplines, with a focus on pre-procedural planning, simulation (rehearsal) of non-routine procedures, and on medical education and training. A review of the latest multidisciplinary literature on the subject offers a general summary of the advances enabled by 3D printing. Numerous advantages and applications were found, such as gaining better insight into patient-specific anatomy, better pre-operative planning, mock simulated surgeries, simulation-based training and education, development of surgical guides and other tools, patient-specific implants, bioprinted organs or structures, and counseling of patients. It was evident that pre-procedural planning and rehearsing of unusual or difficult procedures and training of medical professionals in these procedures are extremely useful and transformative.

Keros type I, II, and III was noted in 9.2%, 75.8%, and 15.0% of cases, respectively. Despite some statistically significant correlations, it was not possible to identify the patient age, sex, and side of body clearly correlating with the critical measurements.

Purpose The goal of this study was to develop a complete workflow allowing for conducting computational fluid dynamics (CFD) simulation of airflow through the upper airways based on computed tomography (CT) and cone-beam computed tomography (CBCT) studies of individual adult patients. Methods This study is based on CT images of 16 patients. Image processing and model generation of the human nasal cavity and paranasal sinuses were performed using open-source and freeware software. 3-D Slicer was used primarily for segmentation and new surface model generation. Further processing was done using Autodesk® Meshmixer TM. The governing equations are discretized by means of the finite volume method. Subsequently, the corresponding algebraic equation systems were solved by OpenFOAM software. Results We described the protocol for the preparation of a 3-D model of the nasal cavity and paranasal sinuses and highlighted several problems that the future researcher may encounter. The CFD results were presented based on examples of 3-D models of the patient 1 (norm) and patient 2 (pathological changes). Conclusion The short training time for new user without a prior experience in image segmentation and 3-D mesh editing is an important advantage of this type of research. Both CBCT and CT are useful for model building. However, CBCT may have limitations. The Q criterion in CFD illustrates the considerable complication of the nasal flow and allows for direct evaluation and quantitative comparison of various flows and can be used for the assessment of nasal airflow.

The First Bite Syndrome is a rare late (1-2 months) post operation complication of surgery in the infratemporal fossa, parapharyngeal space and especially involving the deep lobe of parotid gland. Sometimes it can significantly worsen the patient's quality of life. Acute, sudden, short time pain in the parotid gland region with irradiation to the ear during the first bite a meal is a characteristic for this syndrome. The correct diagnosis and individual approach in choosing a treatment method is the key to success in treating this complication. The purpose of our article is to supplement scanty data on this complication in Polish literature.

We aimed to develop a model to quantitatively assess the potential effectiveness of face shield (visor) in reducing airborne transmission risk of the novel coronavirus SARS-CoV-2 during the current COVID-19 pandemic using the computational fluid dynamics (CFD) method. The studies with and without face shield in both an infected and healthy person have been considered in indoor environment simulation. In addition to the influence of the face shield and the synchronization of the breathing process while using the device, we also simulated the effect of small air movements on the SARS-CoV-2 infection rate (outdoor environment simulation). The contact with infectious particles in the case without a face shield was 12–20 s (s), in the presence of at least one person who was positive for SARS-CoV-2. If the infected person wore a face shield, no contact with contaminated air was observed during the entire simulation time (80 s). The time of contact with contaminated air (infection time) decreases to about 11 s when the surrounding air is still and begins to move at a low speed. Qualitative differences between simulations performed on the patients with and without the face shield are clearly visible. The maximum prevention of contagion is probably a consequence of wearing a face shield by an infected person. Our results suggest that it is possible to determine contact with air contaminated by SARS-CoV-2 using the CFD method under realistic conditions for virtually any situation and configuration. The proposed method is probably the fastest and most reliable among those based on CFD-based techniques.