The effect of short-chain branching (SCB) on the persistence length l p of polyethylene (PE) was studied using small-angle neutron scattering (SANS). In thermodynamically good solvents, l p can be measured directly from the scattering vector q tr at the crossover from good solvent mass-fractal scaling to the rodlike persistent scaling, using the unified equation described in the text. The method was used to study l p of both linear and branched PE in deuterated p-xylene, which is a good solvent for PE at 125 °C. The results indicate an increase in l p of the backbone chain with increasing SCB content, independently measured using Fourier transform infrared spectroscopy (FTIR). These results corroborate the behavior previously reported in Monte Carlo simulations of short-chain branched polymers. A functional relationship for l p in terms of the number of SCBs is proposed.

X‐ray diffraction patterns of linear and branched polyethylenes typically show two sharp reflections and an amorphous halo. The position of the halo depends on branch content and temperature. A single curve describes the position of the halo maximum (2θhalo) for a range of liquid hydrocarbons and polyethylenes in the 20–140°C range. At temperatures well below their melting point, branched polymers give 2θhalo values which differ significantly from those observed for the liquid Linear polymers show a greater divergence, indicating that some of the material giving rise to the halo is much better packed than in the liquid.Parallel 13 C NMR spin‐lattice relaxation studies suggest that this relatively ordered material has a trans conformation but a low average T1c value. © 1993 John Wiley & Sons, Inc.

SYNOPSISThe characterization of short chain branching in polyethylene using transmission FTIR spectroscopy is investigated. Traditional methodologies, using the methyl deformation band for qualitative and quantitative analyses, have recognized shortcomings. The methyl and methylene rocking bands, which are more characteristic of short chain branch type, were found to be more useful. Methyl, ethyl, butyl, isobutyl, and hexyl branches are qualitatively and quantitatively characterized in LLDPE copolymers by FTIR spectroscopy. Methyl branches were characterized by an absorbance at 935 cm-', ethyl branches at 770 cm-', butyl branches at 893 cm-', isobutyl branches at 920 cm-', and hexyl branches at 888 cm-' . Fourier self-deconvolution was used to resolve overlapping bands for ethyl, butyl, and isobutyl branches. Using calibrations derived for LLDPE copolymers from 13C NMR data, FTIR spectroscopy was also used to characterize LLDPE terpolymers and LDPE resins. The FTIR and NMR data are in qualitative and quantitative agreement. In some cases corrections were made to the FTIR results using data obtained from the methyl deformation band. The FTIR technique is less costly and faster than NMR spectroscopy.

Small-angle neutron scattering (SANS) is employed to investigate the structure and longchain branch (LCB) content of metallocene-catalyzed polyethylene (PE). A novel scaling approach is applied to SANS data to determine the mole fraction branch content (φ br ) of LCBs in PE. The approach also provides the average number of branch sites per chain (n br ) and the average number of branch sites per minimum path (n br,p ). These results yield the average branch length (z br ) and number of inner segments n i , giving further insight into the chain architecture. The approach elucidates the relationship between the structure and rheological properties of branched polymers. This SANS method is the sole analytic measure of branch-onbranch structure and average branch length for topologically complex macromolecules.

The dynamic mechanical properties of homogeneous copolymers of ethylene with 1‐butene, 1‐octene, and 1‐octadecene prepared by means of a vanadium‐based catalyst system have been determined. The 1‐butene copolymers show α′ and α transitions in the 20–60°C temperature range, whereas the 1‐octene and 1‐octadecene copolymers show single α transitions. The intensity of the β transition increases with comonomer content in 1‐butene and 1‐octene copolymers and also with the amount of interfacial material present. In ethylene‐1‐octadecene copolymers, this intensity is comparatively low, even though there is about 20% interfacial material present. The implications of these results with regard to the nature of interfacial material are discussed.