Lithium metal is known to possess a very high theoretical capacity of 3,842 mAh g À 1 in lithium batteries. However, the use of metallic lithium leads to extensive dendritic growth that poses serious safety hazards. Hence, lithium metal has long been replaced by layered lithium metal oxide and phospho-olivine cathodes that offer safer performance over extended cycling, although significantly compromising on the achievable capacities. Here we report the defect-induced plating of metallic lithium within the interior of a porous graphene network. The network acts as a caged entrapment for lithium metal that prevents dendritic growth, facilitating extended cycling of the electrode. The plating of lithium metal within the interior of the porous graphene structure results in very high specific capacities in excess of 850 mAh g À 1 . Extended testing for over 1,000 charge/discharge cycles indicates excellent reversibility and coulombic efficiencies above 99%.

The recent interest and excitement in graphene has also opened up a pandora's box of other two-dimensional (2D) materials and material combinations which are now beginning to come to the fore. One family of these emerging 2D materials is transition metal dichalcogenides (TMDs). So far there is very limited understanding on the wetting behavior of "monolayer" TMD materials. In this study, we synthesized large-area, continuous monolayer tungsten disulfide (WS2) and molybdenum disulfide (MoS2) films on SiO2/Si substrates by the thermal reduction and sulfurization of WO3 and MO3 thin films. The monolayer TMD films displayed an advancing water contact angle of ∼83° as compared to ∼90° for the bulk material. We also prepared bilayer and trilayer WS2 films and studied the transition of the water contact angle with increasing number of layers. The advancing water contact angle increased to ∼85° for the bilayer and then to ∼90° for the trilayer film. Beyond three layers, there was no significant change in the measured water contact angle. This type of wetting transition indicates that water interacts to some extent with the underlying silica substrate through the monolayer TMD sheet. The experimentally observed wetting transition with numbers of TMD layers lies in-between the predictions of one continuum model that considers only van der Waals attractions and another model that considers only dipole-dipole interactions. We also explored wetting as a function of aging. A clean single-layer WS2 film (without airborne contaminants) was shown to be strongly hydrophilic with an advancing water contact angle of ∼70°. However, over time, the sample ages as hydrocarbons and water present in air adsorb onto the clean WS2 sheet. After ∼7 days, the aging process is completed and the advancing water contact angle of the aged single-layer WS2 film stabilizes at ∼83°. These results suggest that clean (i.e., nonaged) monolayer TMDs are hydrophilic materials. We further show that substitution of sulfur atoms by oxygen in the lattice of aged monolayer WS2 and MoS2 films can be used to generate well-defined 'hydrophobic-hydrophilic' patterns that preferentially accumulate and create microdrop arrays on the surface during water condensation and evaporation experiments.

The static and dynamic wetting properties of a 3D graphene foam network are reported. The foam is synthesized using template-directed chemical vapor deposition and contains pores several hundred micrometers in dimension while the walls of the foam comprise few-layer graphene sheets that are coated with Teflon. Water contact angle measurements reveal that the foam is superhydrophobic with an advancing contact angle of ∼163 degrees while the receding contact angle is ∼143 degrees. The extremely water repellent nature of the foam is also confirmed when impacting water droplets are able to completely rebound from the surface. Such superhydrophobic graphene foams show potential in a variety of applications ranging from anti-sticking and self-cleaning to anti-corrosion and low-friction coatings.

Previous studies of the interaction of water with graphene-coated surfaces have been limited to flat (smooth) surfaces. Here we created a rough surface by nanopatterning and then draped the surface with a single-layer graphene sheet. We found that the ultrasheer graphene drape prevents the penetration of water into the textured surface thereby drastically reducing the contact angle hysteresis (which is a measure of frictional energy dissipation) and preventing the liquid contact line from getting pinned to the substrate. This has important technological implications since the main obstacle to the motion of liquid drops on rough surfaces is contact angle hysteresis and contact line pinning. Graphene drapes could therefore enable enhanced droplet mobility which is required in a wide range of applications in micro and nanofluidics. Compared to polymer coatings that could fill the cavities between the nano/micropores or significantly alter the roughness profile of the substrate, graphene provides the thinnest (i.e., most sheer) and most conformal drape that is imaginable. Despite its extreme thinness, the graphene drape is mechanically robust, chemically stable, and offers high flexibility and resilience which can enable it to reliably drape arbitrarily complex surface topologies. Graphene drapes may therefore provide a hitherto unavailable ability to tailor the dynamic wettability of surfaces for a variety of applications.

No abstract