Two-tier micro- and nanoscale quasi-periodic self-organized structures, mimicking the surface of a lotus Nelumbo nucifera leaf, were fabricated on titanium surfaces using femtosecond laser ablation. The first tier consisted of large grainlike convex features between 10 and 20 μm in size. The second tier existed on the surface of these grains, where 200 nm (or less) wide irregular undulations were present. The introduction of the biomimetic surface patterns significantly transformed the surface wettabilty of the titanium surface. The original surface possessed a water contact angle of θ(W) 73 ± 3°, whereas the laser-treated titanium surface became superhydrophobic, with a water contact angle of θ(W) 166 ± 4°. Investigations of the interaction of S. aureus and P. aeruginosa with these superhydrophobic surfaces at the surface-liquid interface revealed a highly selective retention pattern for two pathogenic bacteria. While S. aureus cells were able to successfully colonize the superhydrophobic titanium surfaces, no P. aeruginosa cells were able to attach to the surface (i.e., any attached bacterial cells were below the estimated lower detection limit).

Superhydrophobic titanium surfaces fabricated by femtosecond laser ablation to mimic the structure of lotus leaves were assessed for their ability to retain coccoid bacteria. Staphylococcus aureus CIP 65.8T, S. aureus ATCC 25923, S. epidermidis ATCC 14990T and Planococcus maritimus KMM 3738 were retained by the surface, to varying degrees. However, each strain was found to preferentially attach to the crevices located between the microscale surface features. The upper regions of the microscale features remained essentially cell-free. It was hypothesised that air entrapped by the topographical features inhibited contact between the cells and the titanium substratum. Synchrotron SAXS revealed that even after immersion for 50 min, nano-sized air bubbles covered 45% of the titanium surface. After 1 h the number of cells of S. aureus CIP 65.8T attached to the lotus-like titanium increased to 1.27×10(5) mm(-2), coinciding with the replacement of trapped air by the incubation medium.

Medical implants are commonly used in modern medicine but still harbor the risk of microbial infections caused by bacterial biofilms. As their retrospective treatment is difficult, there is a need for biomedical materials that inhibit bacterial colonization from the start without using antibacterial agents, as these can promote resistance development. The promising concept of slippery liquid-infused porous surfaces (SLIPS) possesses enormous potential for this purpose. In the present study, this principle was applied to titanium, a common material in implantology, and its biofilm-repellent properties were demonstrated. To simplify prospective approval of the medical device and to avoid chemical contamination, surface structuring was performed by ultrashort pulsed laser ablation. Four different structures (hierarchical micro- and nanosized spikes, microsized grooves, nanosized ripples, and unstructured surfaces) and five infusing perfluoropolyethers of different viscosities were screened; the best results were obtained with the biomimetic, hierarchical spike structure combined with lubricants of medium viscosities (20-60 cSt at 37 °C, 143 AZ, and GPL 104). The surfaces exhibited extremely low contact angle hysteresis, as is typical for liquid-infused materials and a reliable 100-fold reduction of human oral pathogen Streptococcus oralis biofilms. This characteristic was maintained after exposure to shear forces and gravity. The titanium SLIPS also inhibited adherence of human fibroblasts and osteoblasts. Toxicity tests supported the explanation that solely the surface's repellent properties are responsible for the vigorous prevention of the adhesion of bacteria and cells. This use of physically structured and liquid-infused titanium to avoid bioadhesion should support the prevention of bacterial implant-associated infections without the use of antibacterial agents.

SummaryThe microstructure investigated in this study was inspired by the anisotropic microornamentation of scales from the ventral body side of the California King Snake (Lampropeltis getula californiae). Frictional properties of snake-inspired microstructured polymer surface (SIMPS) made of epoxy resin were characterised in contact with a smooth glass ball by a microtribometer in two perpendicular directions. The SIMPS exhibited a considerable frictional anisotropy: Frictional coefficients measured along the microstructure were about 33% lower than those measured in the opposite direction. Frictional coefficients were compared to those obtained on other types of surface microstructure: (i) smooth ones, (ii) rough ones, and (iii) ones with periodic groove-like microstructures of different dimensions. The results demonstrate the existence of a common pattern of interaction between two general effects that influence friction: (1) molecular interaction depending on real contact area and (2) the mechanical interlocking of both contacting surfaces. The strongest reduction of the frictional coefficient, compared to the smooth reference surface, was observed at a medium range of surface structure dimensions suggesting a trade-off between these two effects.

In this study we investigate the potential of femtosecond laser generated micrometer sized spike structures as functional surfaces for selective cell controlling. The spike dimensions as well as the average spike to spike distance can be easily tuned by varying the process parameters. Moreover, negative replications in soft materials such as silicone elastomer can be produced. This allows tailoring of wetting properties of the spike structures and their negative replicas representing a reduced surface contact area. Furthermore, we investigated material effects on cellular behavior. By comparing human fibroblasts and SH-SY5Y neuroblastoma cells we found that the influence of the material was cell specific. The cells not only changed their morphology, but also the cell growth was affected. Whereas, neuroblastoma cells proliferated at the same rate on the spike structures as on the control surfaces, the proliferation of fibroblasts was reduced by the spike structures. These effects can result from the cell specific adhesion patterns as shown in this work. These findings show a possibility to design defined surface microstructures, which could control cellular behavior in a cell specific manner.