This article describes the preparation and analysis of macroporous TiO2 films on Ti surfaces, for application in bone tissue-Ti implant interfaces. These TiO2 bioceramic films have a macroporous structure consisting of monodisperse, three-dimensional, spherical, interconnected pores adjustable in the micron size range. Micron-sized polystyrene (PS) bead templates are used to precisely define the pore size, creating macroporous TiO2 films with 0.50, 16, and 50 microm diameter pores, as shown by scanning electron microscopy. X-ray photoelectron spectroscopy shows the films to be predominantly composed of TiO2, with approximately 10% carbon. X-ray diffraction reveal rutile as the main phase when fired to the optimal temperature of 950 degrees C. Preliminary experiments find that the in vitro proliferation of human bone-derived cells (HBDC) is similar on all three pore sizes. However, higher [3H]thymidine incorporation by the HBDC is observed when they are grown on 0.50- and 16-microm pores compared to the 50-microm pores, suggesting an enhanced cell proliferation for the smaller pores.

Various surface modifications have been applied to titanium alloy (Ti-6Al-4V) implants, in an attempt to enhance osseointegration; crucial for ideal prosthetic fixation. Despite the numerous studies demonstrating that peptide-modified surfaces influence in vitro cellular behavior, there is relatively little data reporting their effects on bone remodeling. The objective of this article was to examine the effects of chemically modifying Ti-6Al-4V surfaces with a common RGD sequence, a 15-residue peptide containing GRGDSP (glycine-arginine-glycine-aspartate-serine-proline), on the modulation of bone remodeling. The expression of proteins known to be associated with osseous matrix and bone resorption were studied during the growth of human bone-derived cells (HBDC) on these peptide-modified surfaces. HBDC grown for 7 days on RGD surfaces displayed significantly increased levels of osteocalcin, and pro-collagen Ialpha1 mRNAs, compared with the production by HBDC grown on the native Ti-6Al-4V. A pattern that was also reflected at the protein levels for osteocalcin, type I collagen, and bone sialoprotein. Moreover, HBDC grown for 7 and 14 days on RGD-modified Ti-6Al-4V expressed significantly higher level of osteoclast differentiation factors and lower levels of osteoprotegerin and IL-6 proteins compared with other surfaces tested. These results suggest that different chemical treatments of implant material (Ti-6Al-4V) surface result in differential bone responses, not only their ability to form bone but also to stimulate osteoclastic formation.

The photodetachment of the O(2)(-).H(2)O cluster anion at 780 and 390 nm is investigated in comparison with O(2)(-) using photoelectron imaging spectroscopy. Despite the pronounced shift in the photoelectron spectra, the monohydration has little effect on the photoelectron angular distributions: for a given wavelength and electron kinetic energy (eKE) range, the O(2)(-).H(2)O angular distributions are quantitatively similar to those for bare O(2)(-). This observation confirms that the excess electron in O(2)(-).H(2)O retains the overall character of the 2ppi(g) HOMO of O(2)(-). The presence of H(2)O does not affect significantly the partial wave composition of the photodetached electrons at a given eKE. An exception is observed for slow electrons, where O(2)(-).H(2)O exhibits a faster rise in the photodetachment signal with increasing eKE, as compared to O(2)(-). The possible causes of this anomaly are (i) the long-range charge-dipole interaction between the departing electron and the neutral O(2).H(2)O skeleton affecting the slow-electron dynamics; and (ii) the s wave contributions to the photodetachment, which are dipole-forbidden for pi(g)(-1) transitions in O(2)(-), but formally allowed in O(2)(-).H(2)O due to lower symmetry of the cluster anion and the corresponding HOMO.

No abstract

Articles you may be interested inStudy of Nb2O y (y = 2-5) anion and neutral clusters using anion photoelectron spectroscopy and density functional theory calculations Addition of water to Al 5 O 4 − determined by anion photoelectron spectroscopy and quantum chemical calculations Contributions from two structural isomers in the photoelectron spectrum of Al 3 O 3Ϫ have been isolated using an anion beam hole-burning technique. A kite-shaped structure having a lower electron affinity than the bent rectangle isomer was partially bleached from the ion beam just prior to the photoelectron spectroscopy interaction region. Further, we have performed studies varying the time allowed for cluster formation along with density functional calculations on a feasible structural intermediate that suggest that the kite structure may actually be a precursor to the rectangle structure.