Fly ash (FA) is a major industrial waste generated from power stations that add extra cost for proper disposal. Recent research efforts have consequently focused on developing ways to make use of FA in environmentally sound applications. This study, therefore, investigates the potential ability of raw fly ash (RFA) and polyelectrolyte-coated fly ash (PEFA) to remove cadmium (Cd) from polluted water. Using layer-by-layer approach, functionalized fly ash was coated with 20 layers from 0.03% (v/v) of cationic poly(diallyldimethylammonium chloride) (PDADMAC) and anionic polystyrene sulfonate (PSS) solutions. Both surface morphology and chemical composition of the adsorbent (PEFA) were characterized using Field-Emission Scanning Electron Microscope (FE-SEM), X-Ray Diffraction (XRD), Fourier-Transform Infrared (FTIR), and X-Ray Fluorescence (XRF) techniques. The effects of pH, adsorbent dosage, contact time, initial contaminant concentration, and mixing rate of the adsorption of Cd were also studied in batch mode experiments. Results of the study revealed that a 4.0 g/L dosage of PEFA removed around 99% of 2.0 mg/L of Cd in 15 min at 150 rpm compared to only 27% Cd removal achieved by RFA under the same conditions. Results also showed that adsorption by PEFA followed both Langmuir and Freundlich models with correlation coefficients of 98% and 99%, respectively.

In this work, a novel approach is used to synthesize an iron oxide doped carbon nanotube (CNT) membrane, with the goal of fully utilizing the unique properties of CNTs. No binder is used for the synthesis of the membrane; instead, iron oxide particles serve as a binding agent for holding the CNTs together after sintering at high temperature. The produced membrane exhibited a high water flux and strong fouling resistance. In the first step, CNTs were impregnated with various loadings of iron oxide (1, 10, 20, 30 and 50%) via wet chemistry techniques. Impregnated CNTs were then compacted at 200 MPa and sintered at 1350 °C for 5 h to form a compact disk. The membranes were analysed by measuring their porosity, contact angle, diametrical compression test and water flux. The flux of pure water was observed to increase with an increase in iron oxide content. The permeate flux and rejection rate of sodium alginate (SA) were determined to predict the antifouling behavior of the membrane. A maximum removal of 90 and 88% of SA was achieved for membranes with a 10 and 1% iron oxide content, respectively, after 3 h. A minor decline in the permeate flux was observed for all membranes after 4 h of operation.

No abstract

This study investigates the effect of micron-sized nickel particle additions on the microstructural, thermal, and mechanical property changes of α-sialon ceramic composites. The α-sialon/Ni composites were synthesized with an increasing amount of Ni (10–40 wt.%) using the spark plasma sintering technique and nanosized alpha precursors at a relatively low synthesis temperature of 1500 °C with a holding time of 30 min in each case. The density of the samples increased with the increase in Ni content of up to 15 wt.% and, with the further increase in Ni content, it became almost constant with a slight decrease. Furthermore, thermal conductivity and thermal expansion properties of Ni-sialon composites improved slightly with the inclusion of 10 wt.% Ni. The addition of Ni to α-sialon matrix resulted in a decrease in the hardness of the composites from HV10 21.6 to HV10 16.3, however the presence of Ni as a softer interfacial phase resulted in a substantial increase in the fracture toughness of these composites. Fracture toughness was found to increase by approximately 91% at 40 wt.% Ni addition.

Aluminum matrix composites are among the most widely used metal matrix composites in several industries, such as aircraft, electronics, automobile, and aerospace, due to their high specific strength, durability, structural rigidity and high corrosion resistance. However, owing to their low hardness and wear resistance, their usage is limited in demanding applications, especially in harsh environments. In the present work, aluminum hybrid nanocomposite reinforced with alumina (Al2O3) and graphene oxide (GO) possessing enhanced mechanical and thermal properties was developed using spark plasma sintering (SPS) technique. The focus of the study was to optimize the concentration of Al2O3 and GO content in the composite to improve the mechanical and thermal properties such as hardness, compressive strength, heat flow, and thermal expansion. The nanocomposites were characterized by FESEM, EDS, XRD and Raman spectroscopy to investigate their morphology and structural properties. In the first phase, different volume percent of alumina (10%, 20%, 30%) were used as reinforcement in the aluminum matrix to obtain (Al+X% Al2O3) composite with the best mechanical/thermal properties which was found to be 10 V% of Al2O3. In the second phase, a hybrid nanocomposite was developed by reinforcing the (Al + 10 V% Al2O3) with different weight percent (0.25%, 0.5%, 1%) of GO to obtain the optimum composition with improved mechanical/thermal properties. Results revealed that the Al\10 V% Al2O3\0.25 wt.% GO hybrid nanocomposite showed the highest improvement of about 13% in hardness and 34% in compressive strength as compared to the Al\10V% Al2O3 composite. Moreover, the hybrid nanocomposite Al\10 V% Al2O3\0.25 wt.% GO also displayed the lowest thermal expansion.