After hydrothermally treated in H2O (for Mg alloy and Al alloy) or H2O2 (for Ti alloy), microstructured oxide or hydroxide layers were formed on light alloy substrates, which further served as the active layers to boost the self-assembling of 1H,1H,2H,2H-perfluorooctyltriethoxysilane (PFOTES) and finally endowed the substrates with unique wettability, that is, superhydrophobicity. For convenience, the so-fabricated superhyrdophobic surfaces (SHS) were abridged as HT-SHS. For comparison, SHS coded as CE-SHS were also prepared based on chemical etching in acid and succedent surface passivation with PFOTES. To reveal the corrosion protection of these SHS, potentiodynamic polarization measurements in NaCl solution (3.5 wt %) were performed. Moreover, to reflect the long-term stability of these SHS, SHS samples were immersed into NaCl solution and the surface wettability was monitored. Experimental results indicated that HT-SHS was much more stable and effective in corrosion protection as compared with CE-SHS. The enhancement was most likely due to the hydrothermally generated oxide layer by the following tow aspects: on one hand, oxide layer itself can lower the corrosion due to its barrier effect; on the other hand, stronger interfacial bonding is expected between oxide layer and PFOTES molecules.
The design, synthesis and application of iron-based materials (oxides Fe2O3/Fe3O4, hydroxide FeOOH, sulfides FeS2 and their nanocomposites) with 1D, 2D, and 3D nanostructure are fully summarized in this review.
We have prepared a porous, superoleophilic and superhydrophobic miniature oil containment boom (MOCB) for the in situ separation and collection of oils from the surface of water. The MOCB was fabricated by a one-step electrodepositing of Cu2O film on Cu mesh surface without using low surface energy materials. Oils on water surface could be fast contained in the MOCB while water was completely repelled out of the MOCB, thus achieving the separation of oil from water surface. In addition, the contained oil in the MOCB could be in situ collected easily by a dropper, thus achieving the collection of oil. Moreover, the MOCB could be reused for many times in the oil-water separating process with large separation abilities more than 90%. The MOCB also possessed excellent water pressure resistance for about 164 mm water column and good corrosion resistance in simulating seawater. Therefore, the findings in the present study might offer a simple, fast, and low-cost method for the in situ separation and collection of oil spills on seawater surface.
We report a convenient route to fabricate superoleophobic surfaces (abridged as SOS) on copper substrate by combining a two-step surface texturing process (first, the substrate is immersed in an aqueous solution of HNO3 and cetyltrimethyl ammonium bromide, and then in an aqueous solution of NaOH and (NH4)2S2O8) and succeeding surface fluorination with 1H,1H,2H,2H-perfluorodecanethiol (PFDT) or 1-decanethiol. The surface morphologies and compositions were characterized by field emission scanning electron microscopy and X-ray diffraction, respectively. The results showed that spherical micro-pits (SMP) with diameter of 50-100 μm were formed in the first step of surface texturing; in the second step, Cu(OH)2 or/and CuO with structures of nanorods/microflowers/microballs were formed thereon. The surface wettability was further assessed by optical contact angle meter by using water (surface tension of 72.1 mN m(-1) at 20°C), rapeseed oil (35.7 mN m(-1) at 20°C), and hexadecane (25.7 mN m(-1) at 20°C) as probe liquids. The results showed that, as the surface tension decreasing, stricter choosing of surface structures and surface chemistry are required to obtain SOS. Specifically, for hexadecane, which records the lowest surface tension, the ideal surface structures are a combination of densely distributed SMP and nanorods, and the surface chemistry should be tuned by grafted with low-surface-energy molecules of PFDT. Moreover, the stability of the so-fabricated sample was tested and the results showed that, under the testing conditions, superhydrophobicity and superoleophobicity may be deteriorated after wear/humidity resistance test. Such deterioration may be due to the loss of outermost PFDT layer or/and the destruction of the above-mentioned ideal surface structures. For UV and oxidation resistance, the sample remained stable for a period of 10 days.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.