We report a facile strategy to synthesize the nanocomposite of Co3O4 nanoparticles anchored on conducting graphene as an advanced anode material for high-performance lithium-ion batteries. The Co3O4 nanoparticles obtained are 10−30 nm in size and homogeneously anchor on graphene sheets as spacers to keep the neighboring sheets separated. This Co3O4/graphene nanocomposite displays superior Li-battery performance with large reversible capacity, excellent cyclic performance, and good rate capability, highlighting the importance of the anchoring of nanoparticles on graphene sheets for maximum utilization of electrochemically active Co3O4 nanoparticles and graphene for energy storage applications in high-performance lithium-ion batteries.

We developed two-step solution-phase reactions to form hybrid materials of Mn 3 O 4 nanoparticles on reduced graphene oxide (RGO) sheets for lithium ion battery applications. Mn 3 O 4 nanoparticles grown selectively on RGO sheets over free particle growth in solution allowed for the electrically insulating Mn 3 O 4 nanoparticles wired up to a current collector through the underlying conducting graphene network. The Mn 3 O 4 nanoparticles formed on RGO show a high specific capacity up to ~900mAh/g near its theoretical capacity with good rate capability and cycling stability, owing to the intimate interactions between the graphene substrates and the Mn 3 O 4 nanoparticles grown atop. The Mn 3 O 4 /RGO hybrid could be a promising candidate material for high-capacity, low-cost, and environmentally friendly anode for lithium ion batteries. Our growth-on-graphene approach should offer a new technique for design and synthesis of battery electrodes based on highly insulating materials.

Graphene has been widely used to dramatically improve the capacity, rate capability, and cycling performance of nearly any electrode material for batteries. However, the binding between graphene and these electrode materials has not been clearly elucidated. Here we report oxygen bridges between graphene with oxygen functional groups and NiO from analysis by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy and confirm the conformation of oxygen bridges by the first-principles calculations. We found that NiO nanosheets (NiO NSs) are bonded strongly to graphene through oxygen bridges. The oxygen bridges mainly originate from the pinning of hydroxyl/epoxy groups from graphene on the Ni atoms of NiO NSs. The calculated adsorption energies (1.37 and 1.84 eV for graphene with hydroxyl and epoxy) of a Ni adatom on oxygenated graphene by binding with oxygen are comparable with that on graphene (1.26 eV). However, the calculated diffusion barriers of the Ni adatom on the oxygenated graphene surface (2.23 and 1.69 eV for graphene with hydroxyl and epoxy) are much larger than that on the graphene (0.19 eV). Therefore, the NiO NS is anchored strongly on the graphene through a C-O-Ni bridge, which allows a high reversible capacity and excellent rate performance. The easy binding/difficult dissociating characteristic of Ni adatoms on the oxygenated graphene facilitates fast electron hopping from graphene to NiO and thus the reversible lithiation and delithiation of NiO. We believe that the understanding of this oxygen bridge between graphene and NiO will lead to the development of other high-performance electrode materials.

Although the rechargeable lithium–sulfur battery is an advanced energy storage system, its practical implementation has been impeded by many issues, in particular the shuttle effect causing rapid capacity fade and low Coulombic efficiency. Herein, we report a conductive porous vanadium nitride nanoribbon/graphene composite accommodating the catholyte as the cathode of a lithium–sulfur battery. The vanadium nitride/graphene composite provides strong anchoring for polysulfides and fast polysulfide conversion. The anchoring effect of vanadium nitride is confirmed by experimental and theoretical results. Owing to the high conductivity of vanadium nitride, the composite cathode exhibits lower polarization and faster redox reaction kinetics than a reduced graphene oxide cathode, showing good rate and cycling performances. The initial capacity reaches 1,471 mAh g−1 and the capacity after 100 cycles is 1,252 mAh g−1 at 0.2 C, a loss of only 15%, offering a potential for use in high energy lithium–sulfur batteries.

Graphene-sulfur (G-S) hybrid materials with sulfur nanocrystals anchored on interconnected fibrous graphene are obtained by a facile one-pot strategy using a sulfur/carbon disulfide/alcohol mixed solution. The reduction of graphene oxide and the formation/binding of sulfur nanocrystals were integrated. The G-S hybrids exhibit a highly porous network structure constructed by fibrous graphene, many electrically conducting pathways, and easily tunable sulfur content, which can be cut and pressed into pellets to be directly used as lithium-sulfur battery cathodes without using a metal current-collector, binder, and conductive additive. The porous network and sulfur nanocrystals enable rapid ion transport and short Li(+) diffusion distance, the interconnected fibrous graphene provides highly conductive electron transport pathways, and the oxygen-containing (mainly hydroxyl/epoxide) groups show strong binding with polysulfides, preventing their dissolution into the electrolyte based on first-principles calculations. As a result, the G-S hybrids show a high capacity, an excellent high-rate performance, and a long life over 100 cycles. These results demonstrate the great potential of this unique hybrid structure as cathodes for high-performance lithium-sulfur batteries.