No abstract

Railway switches and crossings (S&Cs) are critical, high-value assets in railway networks. A single failure of such an asset could result in severe network disturbance and considerable economical losses. Squats are common rail surface defects of S&Cs and need to be detected and estimated at an early stage to minimise maintenance costs and increase the reliability of S&Cs. For practicality, installation of wired or wireless sensors along the S&C may not be reliable due to the risk of damages of power and signal cables or sensors. To cope with these issues, this study presents a method for collecting and processing vibration data from an accelerometer installed at the point machine to extract features related to the squat defects of the S&C. An unsupervised anomaly-detection method using the isolation forest algorithm is applied to generate anomaly scores from the features. Important features are ranked and selected. This paper describes the procedure of parameter tuning and presents the achieved anomaly scores. The results show that the proposed method is effective and that the generated anomaly scores indicate the health status of an S&C regarding squat defects.

This paper describes the numerical and experimental investigation of the nonlinear vibration of a bladed Jeffcott rotor. The nonlinearity in the system is due to discontinuities caused by multiple contacts with an outer ring as well as the nonlinear deformation of the massless blades. Contacts occur since the rotor shaft is initially misaligned by displacing the outer ring in one direction. The aim of the paper is to develop a simple model of bladed rotor and verify whether the global dynamics of the numerical simulations can be observed experimentally. The experimental rig and data acquisition are presented in detail together with the experimental procedures. The results between the numerical simulation and experiments are compared in terms of bifurcation diagrams and waterfall plots. An overall correlation is observed between the numerical and experimental study in the case of stiff blades, with differences mainly in localized frequency ranges due to parameter variation.

The rail fastening system forms an indispensable part of the rail tracks and needs to be periodically inspected to ensure safe, reliable and sustainable rail operations. Automated visual inspection has gained significant importance for fastener inspection in recent years. Position accuracy, robustness, and practical limitations due to the complex environment are some of the major concerns associated with this method. This study investigates the combined use of image processing and deep learning algorithms for detecting missing clamps within a rail fastening system. The images used for this study was acquired during field inspections carried out along the Borlänge-Avesta line in Sweden. The image processing techniques proposed in this study enabled the improvement of the fastener position and removal of redundant information from the fastener images. In addition, image augmentation was carried out to enhance the data set, ensure experimental reliability and replicate practical challenges associated with such visual inspection. Convolutional neural network and ResNet-50 algorithms are used for classification purposes, and both the algorithms achieved over 98% accuracy during training and validation and over 94% accuracy during the test stage. Both the algorithms also maintained a good balance between the precision and recall scores during the test stage. CNN and ResNet-50 algorithms were also tested to analyse their performances when the clamp areas were covered. CNN was able to accurately predict the fastener state up to 70% of clamp area occlusion, and ResNet-50 was able to achieve accurate predictions up to 75% of clamp area occlusion.

The rail fastening system plays a crucial role in railway tracks as it ensures operational safety by fixing the rail on to the sleeper. Early detection of rail fastener system defects is crucial to ensure track safety and to enable maintenance optimization. Fastener inspections are normally conducted either manually by trained maintenance personnel or by using automated 2-D visual inspection methods. Such methods have drawbacks when visibility is limited, and they are also found to be expensive in terms of system maintenance cost and track possession time. In a previous study, the authors proposed a train-based differential eddy current sensor system based on the principle of electromagnetic induction for fastener inspection that could overcome the challenges mentioned above. The detection in the previous study was carried out with the aid of a supervised machine learning algorithm. This study reports the finding of a case study, along a heavy haul line in the north of Sweden, using the same eddy current sensor system mounted on an in-service freight train. In this study, unsupervised machine learning models for detecting and analyzing missing clamps in a fastener system were developed. The differential eddy current measurement system was set to use a driving field frequency of 27 kHz. An anomaly detection model combining isolation forest (IF) and connectivity-based outlier factor (COF) was implemented to detect anomalies from fastener inspection measurements. To group the anomalies into meaningful clusters and to detect missing clamps within the fastening system, an unsupervised clustering based on the DBSCAN algorithm was also implemented. The models were verified by measuring a section of the track for which the track conditions were known. The proposed anomaly detection model had a detection accuracy of 96.79% and also exhibited a high score of sensitivity and specificity. The DBSCAN model was successful in clustering missing clamps, both one and two missing clamps, from a fastening system separately.