Bacterial cellulose (BC) nanofibres were modified only on their surface using an esterification reaction with acetic acid, hexanoic acid or dodecanoic acid. This reaction rendered the extremely hydrophilic surfaces of BC nanofibres hydrophobic. The hydrophobicity of BC increased with increasing carbon chain length of the organic acids used for the esterification reaction. Streaming (zeta-) potential measurements showed a slight shift in the isoelectric point and a decrease in ζ plateau was also observed after the esterification reactions. This was attributed to the loss of acidic functional groups and increase in hydrophobicity due to esterification of BC with organic acids. A method based on hydrogen/deuterium exchange was developed to evaluate the availability of surface hydroxyl groups of neat and modified BC. The thermal degradation temperature of modified BC sheets decreased with increasing carbon chain length of the organic acids used. This is thought to be a direct result of the esterification reaction, which significantly reduces the packing efficiency of the nanofibres because of a reduction in the number of effective hydrogen bonds between them.

The deformation micromechanics of bacterial cellulose (BC) and microfibrillated cellulose (MFC) networks have been investigated using Raman spectroscopy. The Raman spectra of both BC and MFC networks exhibit a band initially located at ≈ 1095 cm(-1). We have used the intensity of this band as a function of rotation angle of the specimens to study the cellulose fibril orientation in BC and MFC networks. We have also used the change in this peak's wavenumber position with applied tensile deformation to probe the stress-transfer behavior of these cellulosic materials. The intensity of this Raman band did not change significantly with rotation angle, indicating an in-plane 2D network of fibrils with uniform random orientation; conversely, a highly oriented flax fiber exhibited a marked change in intensity with rotation angle. Experimental data and theoretical analysis shows that the Raman band shift rate arising from deformation of networks under tension is dependent on the angles between the axis of fibrils, the strain axis, the incident laser polarization direction, and the back scattered polarization configurations. From this analysis, the effective moduli of single fibrils of BC and MFC in the networks were estimated to be in the ranges of 79-88 and 29-36 GPa, respectively. It is shown also that for the model to fit the data it is necessary to use a negative Poisson's ratio for MFC networks and BC networks. Discussion of this in-plane "auxetic" behavior is given.

Understanding the nature of the interface between nanofibers and polymer resins in composite materials is challenging because of the complexity of interactions that may occur between fibers and between the matrix and the fibers. The ability to select the most efficient amount of reinforcement for stress transfer, making a saving on both cost and weight, is also a key part of composite design. The use of Raman spectroscopy to investigate micromechanical properties of laminated bacterial cellulose (BC)/poly(l-lactic) acid (PLLA) resin composites is reported for the first time as a means for understanding the fundamental stress-transfer processes in these composites, but also as a tool to select appropriate processing and volume fraction of the reinforcing fibers. Two forms of BC networks are investigated, namely, one cultured for 3 days and another for 6 days. The mechanical properties of the latter were found to be higher than the former in terms of Young's modulus, stress at failure, and work of fracture. However, their specific Young's moduli (divided by density) were found to be similar. Young's modulus and stress at failure of transparent predominantly amorphous PLLA films were found to increase by 100 and 315%, respectively, for an 18% volume fraction of BC fibers. BC networks cultured for 3 days were shown to exhibit enhanced interaction with PLLA because of their higher total surface area compared, as measured by nitrogen adsorption, to the material cultured for 6 days. This enhanced interaction is confirmed by using the Raman spectroscopic approach, whereby larger band shift rates, of a peak initially located at 1095 cm(-1), with respect to both strain and stress, are observed, which is a quantitative measure of enhanced stress transfer. Thermal analysis (differential scanning calorimetry) and electron microscopy imaging (scanning electron microscopy) of the samples also confirms the enhanced coupling between the resin and the BC networks cultured for 3 days, compared to those cultured for 6 days. These results are shown to have implications for the use of BC networks for composite reinforcement, whereby less material can be used for the same specific mechanical properties. The technique also gives opportunities to study the interfaces in these composite materials in detail.

No abstract