Large axial flow fans are used in forced draft air cooled heat exchangers (ACHEs). Previous studies have shown that adverse operating conditions cause certain sectors of the fan, or the fan as a whole to operate at very low flow rates, thereby reducing the cooling effectiveness of the ACHE. The present study is directed towards the experimental and numerical analyses of the flow in the vicinity of an axial flow fan during low flow rates. This is done to obtain the global flow structure up and downstream of the fan. A near-free-vortex fan, designed for specific application in ACHEs, is used for the investigation. Experimental fan testing was conducted in a British Standard 848, type A fan test facility, to obtain the fan characteristic. Both steady-state and time-dependent numerical simulations were performed, depending on the operating condition of the fan, using the Realizable k-ε turbulence model. Good agreement is found between the numerically and experimentally obtained fan characteristic data. Using data from the numerical simulations, the time and circumferentially averaged flow field is presented. At the design flow rate the downstream fan jet mainly moves in the axial and tangential direction, as expected for a free-vortex design criteria, with a small amount of radial flow that can be observed. As the flow rate through the fan is decreased, it is evident that the down-stream fan jet gradually shifts more diagonally outwards, and the region where reverse flow occur between the fan jet and the fan rotational axis increases. At very low flow rates the flow close to the tip reverses through the fan, producing a small recirculation zone as well as swirl at certain locations upstream of the fan.
The heat transfer characteristics of industrial air-cooled heat exchangers (ACHEs) are dependent on the ability of the fan system to deliver sufficient cooling air. However, under normal operating conditions, variable flow direction and strength often subject peripheral fans to distorted inlet conditions with an attendant reduction in overall volumetric flow rate and cooling capacity. In this paper, a design methodology for single-rotor axial flow fans, appropriate for use in large industrial ACHE’s is presented. The primary motivation for this work was to address the issues of robust off-design performance, in particular, distorted inlet flow tolerance. Using this methodology, two 8-bladed prototype fans (B1 and B2) were designed, built and tested in accordance with BS 848 (Type A) standards. The two B-fans have a hub-tip ratio of xh = 0.4 and employ the Clark Y and NASA LS airfoil profiles respectively. Measured performance characteristics were compared to commercial fan designs (V-, DL- and L-fan) used in existing ACHEs. Results indicate that the B-fans have a higher design point operating efficiency. The B-fans also show a steeper fan static pressure rise characteristic compared to the commercial fans, except for the DL-fan, implying a greater tolerance to pressure fluctuations caused by distorted inflows.
Actuator-disk models (ADMs) use blade element theory to numerically simulate the flow field induced by axial fans. These models give a fair approximation at near design flow rates, but are of poor accuracy at low flow rates. Therefore, the lift/drag (LD) characteristics of two-dimensional (2D) sections along the span of an air-cooled heat exchanger (ACHE) axial fan are numerically investigated, with the future prospect of improving ADMs at these flow conditions. It is found that the blade sectional LD characteristics are similar in shape, but offset from the 2D LD characteristics of the reference airfoil (NASA LS 413 profile) at small angles of attack (αatt<5deg). A deviation between these characteristics is observed at higher angles of attack. The blade sectional lift coefficients for αatt>5deg always remain lower compared to the maximum lift coefficient of the reference airfoil. Conversely, the blade sectional drag coefficients are always higher compared to that of the reference airfoil for αatt>5deg.
Numerical modeling of the flow field in the vicinity of large axial flow fans finds application in various engineering investigations, whether for fan design purposes, fan induced flow fields or fan system modeling. These three-dimensional fan models generally require verification with experimental results to establish validity. For this purpose a comparison is generally made between the numerically and experimentally obtained fan performance characteristics (fan static pressure and static efficiency curves) to verify the model. Although this method provides a means to validate the numerical model on a global flow level, some uncertainty on the accuracy of this validated model on a local flow level (flow structures close to the fan blade) might still exist. In the present study an experimental technique is presented to measure blade surface static pressures that can be used to validate numerical fan models on a local flow level. These measurements are obtained for a specific fan by means of piezo-resistive pressure transducers mounted in a capsule on the fan axis and connected to pressure taps in specially manufactured fan blades. The transducers are also coupled to a telemetry system that samples the measured pressures and enables wireless communication between the fan and a laptop/PC. Blade surface pressure measurements are obtained for a series of volumetric flow rates through the fan and compared to the numerical data simulated using a RANS approach. A good comparison between the experimental and numerical blade surface static pressure data exists, with the largest discrepancies occurring near the hub as well as the leading and trailing edges of the blade. The reason for this discrepancy could be attributed, amongst others, to low y+ values (y+ < 30) on the blade surface in these regions, leading to errors in the calculation of the wall condition by the wall function. The experimental technique therefore provides CFD engineers with an additional tool for numerical fan model validation on a local flow level.
The MinWaterCSP project was defined with the aim of reducing the cooling system water consumption and auxiliary power consumption of concentrating solar power (CSP) plants. A full-scale, 24 ft (7.315 m) diameter model of the M-fan was subsequently installed in the Min WaterCSP cooling system test facility, located at Stellenbosch University. The test facility was equipped with an in-line torque arm and speed transducer to measure the power transferred to the fan rotor, as well as a set of rotating vane anemometers upstream of the fan rotor to measure the air volume flow rate passing through the fan. The measured results were compared to those obtained on the 1.542 m diameter ISO 5801 test facility using the fan scaling laws. The comparison showed that the fan power values correlated within +/− 7% to those of the small-scale fan, but at a 1° higher blade setting angle for the full-scale fan. To correlate the expected fan static pressure rise, a CFD analysis of the 24 ft (7.315 m) diameter fan installation was performed. The predicted fan static pressure rise values from the CFD analysis were compared to those measured on the 1.542 m ISO test facility, for the same fan. The simulation made use of an actuator disc model to represent the effect of the fan. The results showed that the predicted results for fan static pressure rise of the installed 24 ft (7.315 m) diameter fan correlated closely (smaller than 1% difference) to those of the 1.542 m diameter fan at its design flowrate but, once again, at approximately 1° higher blade setting angle.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2025 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.