No abstract

No abstract

The behavior of nickel-titanium instruments depends largely on the cross-section of the working part. The effect of pitch length was evaluated using two instruments with the same cross-section (triple helix; 0.6% taper). One had a short pitch (0.5 mm at the tip to 0.9 mm at 16 mm at the end of the working part). The other had a long pitch (1.18 mm/2 mm). A dynamometer recorded tensional stress (MHz) and the tendency to screw in (Fz) during simulated canal preparations. Rotational speed was kept constant, and a continuous pecking movement was used. At the end of the preparations, the average Fz was 5.02 N for the short-pitch instrument and 1.47 N for the long-pitch instrument (p < 0.001). The average Mz varied from 0.88 N (short pitch) to 0.35 N (long pitch). Increasing the pitch decreased torsional load sharing and the tendency to screw in.

BackgroundThe aim was to compare the efficacy of the passive ultrasonic irrigation PUI and the Xp-endo Finisher (FKG-Dentaire, La-Chaux-de-Fonds, Switzerland) in removing the calcium hydroxide paste from root canals and from the apical third.Material and MethodsSixty-eight root canals of single-rooted teeth were shaped using the BT-Race files (FKG-Dentaire, La-Chaux-de-Fonds, Switzerland). Ca(OH)2 was placed in all samples except for the negative control group (n=4). Remaining teeth were randomly divided into three groups: G1-Xp (n=30), G2-PUI (n=30) and the positive control group (n=4). Removal procedure consisted of three repeated one-minute-cycles. Samples were split longitudinally, photos of halves were taken at X6.4 magnification and were analyzed using the ImageJ-Software (The National Institutes of Health NIH, Bethesda, Maryland, USA) to calculate the percentage of surfaces with residual Ca(OH)2; the results were compared using the Wilcoxon-Mann Whitney test. Photos of the apical thirds were taken at X16 and X40 magnifications and were scored by two examiners from (0) to (4). Scores of the apical third were compared using the Fisher test.ResultsThe Xp-endo Finisher removed completely the Ca(OH)2 dressing from four teeth (13.33%) whereas the PUI in one tooth (3.33%). The mean values of the remaining Ca(OH)2 were (2.1%, 3.6%) respectively and the difference was not significant (p= 0.195). Both examiners found the Xp-endo Finisher more efficient in the apical third and the difference was significant; p= (0.025, 0.047) respectively.ConclusionsThe Xp-endo Finisher showed a superiority over the PUI in removing the Ca(OH)2 from the apical third after 3 minutes of activation. Key words:Calcium hydroxide removal, Passive ultrasonic irrigation, Xp-endo Finisher.

Root canal segmentation on cone beam computed tomography (CBCT) images is difficult because of the noise level, resolution limitations, beam hardening and dental morphological variations. An image processing framework, based on an adaptive local threshold method, was evaluated on CBCT images acquired on extracted teeth. A comparison with high quality segmented endodontic images on micro computed tomography (µCT) images acquired from the same teeth was carried out using a dedicated registration process. Each segmented tooth was evaluated according to volume and root canal sections through the area and the Feret's diameter. The proposed method is shown to overcome the limitations of CBCT and to provide an automated and adaptive complete endodontic segmentation. Despite a slight underestimation (-4, 08%), the local threshold segmentation method based on edge-detection was shown to be fast and accurate. Strong correlations between CBCT and µCT segmentations were found both for the root canal area and diameter (respectively 0.98 and 0.88). Our findings suggest that combining CBCT imaging with this image processing framework may benefit experimental endodontology, teaching and could represent a first development step towards the clinical use of endodontic CBCT segmentation during pulp cavity treatment.