Summary Particulate pollution is a serious health problem throughout the world, exacerbating a wide range of respiratory and vascular illnesses in urban areas. The use of trees to reduce the effects of these pollutants has been addressed in the literature, but has rarely been quantified. The aim of the present study was to quantify the effectiveness of five tree species − pine (Pinus nigra var. maritima), cypress ( × Cupressocyparis leylandii), maple (Acer campestre), whitebeam (Sorbus intermedia), poplar (Populus deltoides × trichocarpa‘Beaupré’) − in capturing pollutant particles. This was achieved by exposing them to NaCl droplets of approximately 1 μm diameter at a range of windspeeds in two windtunnels. The deposition velocity (Vg) and particle trapping efficiency (Cp) were calculated from these exposures. In addition, a variable dependent on foliage structure [Stokes number (St)] was correlated with Cp to gauge the effect of tree morphology on particle capture. Maximum Cp values ranged from 2.8% for P. nigra, to 0.12% and 0.06% for P. trichocarpa×deltoides and A. campertre, respectively. The finer, more complex structure of the foliage of the two conifers (P. nigra and C. leylandii) explained their much greater effectiveness at capturing particles. The data presented here will be used to model the effectiveness of tree planting schemes in improving urban air quality by capturing pollutant particles.

No abstract

No abstract

Trees are used to produce a variety of wood-based products including timber, pulp and paper. More recently, their use as a source of renewable energy has also been highlighted, as has their value for carbon mitigation within the Kyoto Protocol. Relative to food crops, the domestication of trees has only just begun; the long generation time and complex nature of juvenile and mature growth forms are contributory factors. To accelerate domestication, and to understand further some of the unique processes that occur in woody plants such as dormancy and secondary wood formation, a 'model' tree is needed. Here it is argued that Populus is rapidly becoming accepted as the 'model' woody plant and that such a 'model' tree is necessary to complement the genetic resource being developed in arabidopsis. The genus Populus (poplars, cottonwoods and aspens) contains approx. 30 species of woody plant, all found in the Northern hemisphere and exhibiting some of the fastest growth rates observed in temperate trees. Populus is fulfilling the 'model' role for a number of reasons. First, and most important, is the very recent commitment to sequence the Populus genome, a project initiated in February 2002. This will be the first woody plant to be sequenced. Other reasons include the relatively small genome size (450-550 Mbp) of Populus, the large number of molecular genetic maps and the ease of genetic transformation. Populus may also be propagated vegetatively, making mapping populations immortal and facilitating the production of large amounts of clonal material for experimentation. Hybridization occurs routinely and, in these respects, Populus has many similarities to arabidopsis. However, Populus also differs from arabidopsis in many respects, including being dioecious, which makes selfing and back-cross manipulations impossible. The long time-to-flower is also a limitation, whilst physiological and biochemical experiments are more readily conducted in Populus compared with the small-statured arabidopsis. Recent advances in the development of large expressed sequence tagged collections, microarray analysis and the free distribution of mapping pedigrees for quantitative trait loci analysis secure Populus as the ideal subject for further exploitation by a wide range of scientists including breeders, physiologists, biochemists and molecular biologists. In addition, and in contrast to other model plants, the genus Populus also has genuine commercial value as a tree for timber, plywood, pulp and paper.

Energy crops currently contribute a relatively small proportion to the total energy produced from biomass each year, but the proportion is set to grow over the next few decades. This paper reviews the current status of energy crops and their conversion technologies, assesses their potential to contribute to global energy demand and climate mitigation over the next few decades, and examines the future prospects. Previous estimates have suggested a technical potential for energy crops of $ 400 EJ yr À1 by 2050. In a new analysis based on energy crop areas for each of the IPCC SRES scenarios in 2025 (as projected by the IMAGE 2.2 integrated assessment model), more conservative dry matter and energy yield estimates and an assessment of the impact on non-CO 2 greenhouse gases were used to estimate the realistically achievable potential for energy crops by 2025 to be between 2 and 22 EJ yr À1 , which will offset $ 100-2070 Mt CO 2 -eq. yr À1 . These results suggest that additional production of energy crops alone is not sufficient to reduce emissions to meet a 550 lmol mol À1 atmospheric CO 2 stabilization trajectory, but is sufficient to form an important component in a portfolio of climate mitigation measures, as well as to provide a significant sustainable energy resource to displace fossil fuel resources. Realizing the potential of energy crops will necessitate optimizing the dry matter and energy yield of these crops per area of land through the latest biotechnological routes, with or without the need for genetic modification. In future, the co-benefits of bioenergy production will need to be optimized and methods will need to be developed to extract and refine high-value products from the feedstock before it is used for energy production.