is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. Thermal oxidation in air at atmospheric pressure, in the 80e140 C temperature range and in oxygen at 100 C in the 0.02e3 MPa pressure range, of unvulcanized, unstabilized, unfilled polychloroprene (CR) has been characterized using FTIR and chlorine concentration measurement. The kinetic analysis was focused on double bond consumption. A mechanistic scheme involving unimolecular and bimolecular hydroperoxide decomposition, oxygen addition to alkyl radicals, hydrogen abstraction on allylic methylenes, alkyl and peroxyl additions to double bonds and terminations involving alkyl and peroxy radicals was elaborated. The corresponding rate constants were partly extracted from the literature and partly determined from experimental data using the kinetic model derived from the mechanistic scheme in an inverse approach. Among the specificities of polychloroprene, the following were revealed: The rate of double bond consumption is a hyperbolic function of oxygen pressure that allows a law previously established for the oxidation of saturated substrates to be generalized. CR oxidation is characterized by the absence of an induction period that reveals the instability of hydroperoxides. The kinetic analysis also reveals that peroxyl addition is faster than hydrogen abstraction but slower in CR than in common hydrocarbon polydienes.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. a b s t r a c tTensile properties and crack propagation properties, especially critical strain energy release rate in mode I, G IC , have been used to investigate fracture properties of elastomers and their relationships with microstructure. These investigations were mainly based on a series of comparisons: first, the behaviour of polychloroprene rubber (CR), undergoing stress hardening due to strain induced crystallization (SIC) and oxidative crosslinking (OCL) was compared with that of chlorinated polyethylene (CPE), which undergoes SIC but not OCL, and with a polyurethane based on hydroxyl terminated polybutadiene (PU) which undergoes OCL but not SIC. Comparisons were also made on CR between fracture behaviour at ambient temperature, where SIC occurs and at 100 C where there is no SIC. Finally, oxidative crosslinking was used to vary in a continuous way the crosslink density in CR and PU, in order to evaluate the role of crosslinking in fracture behaviour. The results reveal the strong contribution of SIC to fracture strength. Crosslinking, even at low conversion, inhibits SIC which explains the sharp decrease of CR toughness in the early period of exposure to oxidation. When SIC has disappeared, it is possible to appreciate the effect of crosslinking on fracture behaviour. This effect, as evaluated from the density of deformation energy at rupture in tension or from G IC value, is almost negligible while the sample modulus increases regularly as a consequence of crosslinking. It appears that the toughness remains almost constant because it is under the influence of two contradictory phenomena: the negative effect of a reduction of ultimate elongation and the positive effect of a modulus increase. Such behaviour can be explained in terms of heterogeneous distribution of the lengths of elastically active chains. After long exposure, the sample behaviour becomes brittle, very high modulus values indicate that the samples approach, presumably in a heterogeneous way, the glassy state.

The oxidative ageing in the range of 60 °C-140 °C of sulfur vulcanized polychloroprene has been studied by FTIR spectroscopy (double bond consumption), modulus changes and oxygen absorption measurements. Experiments were carried out on thin films and thick samples to investigate both homogeneous and inhomogeneous (diffusion controlled) oxidation with the goal of establishing the underlying correlation between oxidative degradation chemistry and mechanical property changes. A correlation between oxidatively driven degradation chemistry and modulus is possible using the established approaches of rubber elasticity where an effective crosslinking yield due to double bond reactions is of the order of 30% for this material (i.e. the loss of 3 double bonds results in one effective crosslink associated with material hardening). It is then possible to predict modulus changes induced by oxidation for vulcanized and unstabilized polychloroprene rubber. A kinetic model is introduced with two propagation reactions (hydrogen abstraction and radical addition to double bonds) and two stabilization processes involving sulfur containing moieties from the vulcanization process. The kinetic scheme was solved and the relevant rate constants determined. This model can adequately predict modulus changes in films and thick samples as a function of time and spatially resolved.

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. Water sorption has been studied gravimetrically for polychloroprene rubber samples, first at a fixed hygrometric ratio (98% HR) and several temperatures (25, 40, 60 and 80 C) for samples of 1.8 and 3.8 mm thickness (Constant Temperature and Hygrometry, CTH experiments), then at fixed temperature (40 C) and several hygrometric ratios ranging from 0 to 95% HR on samples of 0.1 mm thickness (DVS experiments). CTH experiments reveal an abnormal sorption behavior: after an apparently fickian transient period, the water absorption continues at almost constant rate, no equilibrium is observed after more than 2500 h, whatever the temperature. DVS experiments reveal a very low Henry's solubility but the formation of clusters at water activities higher than 40%. The water diffusivity is almost independent of activity below 50% HR and decreases rapidly when activity increases above 50%. Contrary to CTH experiments, equilibrium is reached in DVS and the difference is not simply linked to the well-known effect of sample thickness on diffusion rate. The results allow hypotheses such as hydrolysis or osmotic cracking to explain the abnormal sorption phenomenon to be rejected. It is suggested that clusters could be polymerewater complexes having a linear/branched structure able to grow without phase separation that could explain the reversibility of sorptionedesorption cycles. The difference of behavior between thin 0.1 mm and thicker 1.8 or 3.8 mm samples could be due to an effect of swelling stresses. Ó

No abstract