Nowadays, there is a strong demand for inspection systems integrating both high sensitivity under various testing conditions and advanced processing allowing automatic identification of the examined object state and detection of threats. This paper presents the possibility of utilization of a magnetic multi-sensor matrix transducer for characterization of defected areas in steel elements and a deep learning based algorithm for integration of data and final identification of the object state. The transducer allows sensing of a magnetic vector in a single location in different directions. Thus, it enables detecting and characterizing any material changes that affect magnetic properties regardless of their orientation in reference to the scanning direction. To assess the general application capability of the system, steel elements with rectangular-shaped artificial defects were used. First, a database was constructed considering numerical and measurements results. A finite element method was used to run a simulation process and provide transducer signal patterns for different defect arrangements. Next, the algorithm integrating responses of the transducer collected in a single position was applied, and a convolutional neural network was used for implementation of the material state evaluation model. Then, validation of the obtained model was carried out. In this paper, the procedure for updating the evaluated local state, referring to the neighboring area results, is presented. Finally, the results and future perspective are discussed.

Due to the existing relationship between microstructural properties and magnetic ones of the ferromagnetic materials, the application potential of the magnetic Barkhausen noise (BN) method to non-destructive testing is constantly growing. However, the stochastic nature of the Barkhausen effect requires the use of advanced signal processing methods. Recently, the need to apply time-frequency (TF) transformations to the processing of BN signals arose. However, various TF methods have been used in the majority of cases for qualitative signal conditioning and no extensive analysis of TF-based information has been conducted so far. Therefore, in this paper, the wide analysis of BN TF representation was carried out. Considering the properties of TF transformations, the Short-Time Fourier Transform (STFT) was used. A procedure for definition of the envelopes of the TF characteristic was proposed. To verify the quality of extracted features, an analysis was performed on the basis of BN signals acquired during stress loading experiments of steel elements. First, the preliminary experiments were processed for various parameters of the measuring system and calculation procedures. The feature extraction procedure was performed for different modes of TF representations. Finally, the distributions of TF features over the loading stages are presented and their information content was validated using commonly used features derived from time T and frequency F domains.

The paper presents a new approach to obtain information on magnetic anisotropy in Si–Fe grain oriented ferromagnetic steel based on the observation of the magnetic Barkhausen noise (MBN). Until now, in the literature one can only notice the MBN study of magnetic anisotropy in steels carried out in a single time or frequency domain. However, due to the observed high variability of the dynamics of the MBN phenomenon over its occurrence period, depending on the steel properties, the idea of utilization of combined time and frequency representations to obtain new or supplementary information arises. For this purpose, the MBN phenomenon was observed in various directions for steels with oriented magnetic properties. Then, using the short-time Fourier transform, time-frequency (TF) distributions were determined and features vectors enabling the quantification of crucial information were determined. Before performing the final experiments, a series of tests were carried out for different measuring conditions. As a result, it was possible to adjust the conditions enabling us to obtain the highest possible sensitivity for MBN and discrimination level between directional properties in the material. Then, an algorithm of detailed analysis and division of the TF representation into subranges was proposed, enabling the extraction of more detailed information about the phenomena occurring during the magnetization process. This allowed us to clearly indicate and then separate three areas of MBN main activity. Finally, the obtained angular distributions of selected features were presented and discussed, and further conclusions were given.

In this paper the results of utilization of electromagnetic methods operating in low and high frequency range for evaluation of stress state and plastic deformation in steel elements are presented. In low frequency range Barkhausen noise and magnetic hysteresis loop method for evaluation of stress level and growth of plastic deformation changes were utilized. The methods allow to monitor parameters related to magnetization process under AC filed. Additionally in this paper the possibility of utilization of high frequency method for estimation of deformation extent (i.e. elongation) caused by stress will be presented. In this experiment the frequency response (the reflection coefficient S11) is measured. The strong relation of antennas resonant frequency to patch dimensions is utilized in order to obtain information about deformation of the sample.

The paper presents a new approach to non-destructive evaluation of easy/hard magnetization axis in grain-oriented SiFe electrical steels based on the Barkhausen phenomenon and its time-frequency (TF) characteristics. Anisotropy in steels is influenced by a number of factors that formulate the global relationship and affect the Barkhausen effect. Due to the observed high variability in the dynamics of magnetic Barkhausen noise (MBN) over time, obtained for various directions in grain-oriented steel, it becomes justified to conduct MBN signal analyses in the time-frequency domain. This representation allows not only global information from MBN signal over entire period to be expressed, but also detailed relationships between properties in time and in frequency to be observed as well. This creates the opportunity to supplement the information obtained. The main aspect considered in the work is to present a procedure that allows an assessment of the resultant angular characteristics in steel. For this purpose, a sample of a conventional grain-oriented SiFe sheet was used. Measurements were made for several angular settings towards the rolling and transverse directions. A data transformation procedure based on short-time Fourier transform (STFT) as well as quantitative analysis and synthesis of information contained in the TF space was presented. Angular characteristics of selected TF parameters were shown and discussed. In addition, an analysis of the repeatability of information obtained using the proposed procedure under various measurement conditions was carried out. The relationship between the selection of calculation parameters used during transformation and the repeatability of the obtained TF distributions were demonstrated. Then the selection of the final values of the calculation parameters was commented upon. Finally, the conclusions of the work carried out were discussed.