FEA allowed visualisation of the effects that loading on different floor surfaces have on the biomechanics of the claw. Uneven preparation of the claw sole resulted in high stresses at and close to irregularities of the sole. Consequences were more severe on harder flooring. The model supports the hypothesis that mechanical factors play a substantial role in the pathogenesis of claw lesions.

The biomechanical effects of lowering and raising the heels were studied using a finite element (FE) computer model of the equine hoof capsule consisting of 18,635 finite elements. A static load of 3000 N was distributed to nodes of the inner hoof wall (80%) according to the suspension of the coffin bone, 20% loaded sole and frog. When loaded the FE hoof capsules showed the following deformations: the proximal dorsal wall moves back, the quarters flare to the side and sole and frog perform a downward movement. Stresses are high in the material surrounding the quarter nails, in the heels and in the proximal dorsal wall. Three types of horseshoes were simulated, a regular shoe with flat branches, a shoe with 5 degrees raised heels and a shoe with 5 degrees lowered heels. Raising the heels resulted in significantly (P < 0.05) low stress and displacement values. The lowered heels model calculated highest stress and displacement values and the results of the FE model with the regular horseshoe were found in between.

An established finite element model of a bovine claw was used to compare mechanical stress levels in a loaded model claw on different types of flooring. The following situations were compared: a claw standing on a solid floor, a claw standing on the edge of a short tie stand, and claws standing on slatted floors with slats of 28 and 40 mm (wide) running parallel and perpendicular to the claw axis. Finite element analysis allowed visualization of stress peaks seen predominantly in the weight-bearing border of the dorsal abaxial wall and of the bulbar region and in the proximal axial wall. Maximum stress values of 13 MPa were found in the model claw loaded on the solid floor and values of 18 to 22 MPa were seen in the model claw loaded on the edge of the solid floor. On slatted floors, stresses increased in the situation in which the claw was not supported under the abaxial wall. Comparison between the other slatted floors showed little difference in amounts of mechanical stress. A clear distinction was detected between the solid floor with full claw contact and the slatted floors. From the point of view of the mechanical stress seen in finite element analysis, a large contact area between claw and floor, as seen in the solid surface floor, is preferable. When use of slatted floors is unavoidable, direction of the slats should run perpendicular to the direction of the walkway to prevent even more mechanical impact in certain footing situations.

Summary A finite element (FE) hoof capsule was built as a small, symmetrical forelimb hoof on IDEAS* as a model for calculation and visualisation of stress and displacement of the equine hoof capsule. The model's loading was performed according to the suspension of the coffin bone within the hoof wall (pulling force) and over the sole and frog (compressing force) with a total of 3000 N. Restraints of the model's ground nodes and surface wall nodes were defined for simulation of 4 shoeing situations: a regular horseshoe, a horseshoe with a toe clip, a horseshoe with regular side clips and a horseshoe with a toe clip and more caudally‐placed side clips, all fixed to the hoof capsule with 3 nails on each side and each calculated in a tense and a loose nailed condition. Von Mises stresses were taken ranging from 1.22 N/mm2 in the weighthearing border of the side clip shoe fixed loosely to the capsule up to 16.67 N/mm2 in the hoof horn material surrounding the third nail. Further high stress zones were calculated in the proximal dorsal wall, the distal heel and the lateral hoof wall. Displacement values were taken showing movements of hoof wall, sole and frog according to the shoeing conditions. Maximal displacement was calculated in the hoof capsule shod with a regular horseshoe without a clip. Minimal displacement was found in the capsule with a toe clip and 2 side clips placed behind the 3rd nail. All models showed higher displacements when calculated with a loose nail fixation. Validation of the detailed features of the models is not yet possible. Finite element analysis (FEA) can be used practically to predict influences of various farrier techniques on the equine hoof in order to avoid possible harm to horses' feet in field studies.

Finite element modeling is a unique way of introducing technical and material research into medical science. A bovine distal hind limb was scanned using computed tomography for geometric image capture and the data were subsequently divided (segmented) into 4 tissue types: bone, bone marrow, soft tissue, and the horn capsule. Material data from previous studies were integrated into the model. Flexor tendons were assembled as longitudinal structures starting at their cross-sectional areas at the height of the metatarsophalangeal joint, proceeding in the plantaro-distal direction and meeting the distal phalanx at the tuberculum flexorium. Three different flooring situations (full support floor, bearing weight in the abaxial half of the lateral claw and in the dorsal halves of both claws, respectively) were created to evaluate the effects of loading. Full support resulted in von Mises stress levels between 3.5 and 1.5 MPa for the osseous structures and some regions of the segmented soft tissue; stress patterns in the bulb and sole of the claw capsule (1.5 MPa) and in the floor (0.5 MPa) were similar to pressure plate data in vivo and in vitro, with corresponding strain values of 2.4%. Reduced support resulted in higher stresses (up to approximately 8 MPa) in bones, claw capsules, and tendons; high strains ( approximately 11%) were found in the soft tissue, depending on how the floor was constructed. Although the models may still be anatomically improved, stress and strain calculations are possible with results comparable to related research, and the model shows interaction between the 2 digits. This possibly will help with further understanding of the biomechanical function of this 2-digit structure. With respect to clinical interpretation, reduced support to the bovine hind limb increases focal stress peaks in the different tissues, which may indicate a location of potential injury.