No abstract

An apatite layer was formed on polyethyleneterephthalate (PET) substrates by the following biomimetic process. PET substrates were placed on granular particles of a CaO-SiO2-based glass in simulated body fluid (SBF) with ion concentrations nearly equal to those of human blood plasma to form apatite nuclei on their surfaces (first treatment). They then were soaked in modified SBFs, the ion concentrations of which were changed to give a variation in ionic activity product of apatite (IP), in order to make the apatite nuclei grow (second treatment). The Ca/P atomic ratio and the lattice constant c of the formed apatite decreased from 1.54 to 1.40 and from 6.880 to 6.838 A, respectively, with increasing ion concentrations from 0.75 to 2.00 times those of SBF, that is, with increasing IP from 10(-96.6) to 10(-91.9). This was attributed to an increase in the concentration of HPO4(2-) ion substituting for the PO4(3-) ion sites, which gave an increase in the Ca2+ in the apatite. Even the apatite formed in 1.00 SBF showed a Ca/P ratio of 1.51 and lattice constants a of 9.432 A and c of 6.870 A. The Ca/P ratio and lattice constant c were smaller and the lattice constant a was larger than those of the bone apatite; its Ca/P ratio and its lattice constants a and c, were 1.65, 9.419 A, and 6.88 A, respectively. This was attributed to the lower content (2.64 wt%) of the CO3(2-) ion substituting for the PO4(3-) ion sites of the apatite compared to that of the bone apatite (5.80 wt%). The lower content of the CO3(2-) ion in the apatite might be caused by the lower concentration of HCO3- ion in 1.00 SBF compared to that in human blood plasma.

Our previous study showed that titanium metal forms a bonelike apatite layer on its surface in simulated body fluid when it was subjected to NaOH and heat treatments to form a sodium titanate hydrogel or amorphous sodium titanate surface layer. In the present study, bonding strength of the apatite layer formed on the titanium metals to the substrates were examined under tensile stress, in comparison with those of the apatite layers formed on Bioglass 45S5-type glass, dense sintered hydroxyapatite, and glass-ceramic A-W, which are already clinically used. The NaOH-treated titanium metals showed higher bonding strength of the apatite layer to the substrates, which was maximized by heat treatments at 500 and 600 degrees C, than all the examined bioactive ceramics. It is believed that bioactive metals thus obtained are useful as bone substitutes, even under load-bearing conditions.

Apatite layer was formed on polyethyleneterephthalate (PET) substrate by the following biomimetic process. The PET substrate was placed on granular particles of a CaO, SiO2-based glass in simulated body fluid (SBF) with ion concentrations nearly equal to those of human blood plasma to form apatite nuclei on their surfaces. The apatite nuclei was then grown into a continuous layer by subsequently soaking the substrate in SBF under air or CO2 atmosphere in which CO2 partial pressure in the ambient was adjusted to 14.8 kPa to increase the content of carbonate ion to a level nearly equal to that of blood plasma. The increase in the content of carbonate ions in SBF changed the Ca/P atomic ratio of the apatite from 1.51 to 1.63, content of CO(3)2- ions from 2.64 to 4.56 wt %, and lattice constants a from 94.32 to 94.23 nm and c from 68.70 to 68.83 nm, respectively. The Ca/P ratio and lattice constants of the apatite formed in SBF under CO2 atmosphere were approximately identical to those of bone apatite, i.e. Ca/P atomic ratio 1.65, content of CO(3)2- ion 5.80 wt % and lattice constants a 94.20 and c 68.80 nm. This indicates that an apatite with composition and structure nearly identical to those of bone apatite can be produced in SBF by adjusting its ion concentrations including the content of carbonate ions to be equal to those of blood plasma.