Recent studies have demonstrated that the aerothermal characteristics of turbine rotor blade tip under a transonic condition are qualitatively different from those under a low-speed subsonic condition. The cooling injection adds further complexity to the over-tip-leakage (OTL) transonic flow behavior and aerothermal performance, particularly for commonly studied shroudless tip configurations such as a squealer tip. However there has been no published experimental study of a cooled transonic squealer. The present study investigates the effect of cooling injection on a transonic squealer through a closely combined experimental and CFD effort. Part I of this two-part paper presents the first of the kind tip cooling experimental data obtained in a transonic linear cascade environment (exit Mach number 0.95). Transient thermal measurements are carried out for an uncooled squealer tip and six cooling configurations with different locations and numbers of discrete holes. High-resolution distributions of heat transfer coefficient and cooling effectiveness are obtained. ansysFluent is employed to perform numerical simulations for all the experimental cases. The mesh and turbulence modeling dependence is first evaluated before further computational studies are carried out. Both the experimental and computational results consistently illustrate strong interactions between the OTL flow and cooling injection. When the cooling injection (even with a relatively small amount) is introduced, distinctive series of stripes in surface heat transfer coefficient are observed with an opposite trend in the chordwise variations on the squealer cavity floor and on the suction surface rim. Both experimental and CFD results have also consistently shown interesting signatures of the strong OTL flow–cooling interactions in terms of the net heat flux reduction distribution in areas seemingly unreachable by the coolant. Further examinations and analyses of the related flow physics and underlining vortical flow structures will be presented in Part II.

A basic attribute for turbine blade film cooling is that coolant injected should be largely passively convected by the local base flow. However, the effective working of the conventional wisdom may be compromised when the cooling injection strongly interacts with the base flow. Rotor blade tip of a transonic high-pressure (HP) turbine is one of such challenging regions for which basic understanding of the relevant aerothermal behavior as a basis for effective heat transfer/cooling design is lacking. The need to increase our understanding and predictability for high-speed transonic blade tip has been underlined by some recent findings that tip heat transfer characteristics in a transonic flow are qualitatively different from those at a low speed. Although there have been extensive studies previously on squealer blade tip cooling, there have been no published experimental studies under a transonic flow condition. The present study investigates the effect of cooling injection on a transonic squealer tip through a closely combined experimental and computational fluid dynamics (CFD) effort. The experimental and computational results as presented in Part I have consistently revealed some distinctive aerothermal signatures of the strong coolant-base flow interactions. In this paper, as Part II, detailed analyses using the validated CFD solutions are conducted to identify, analyze, and understand the causal links between the aerothermal signatures and the driving flow structures and physical mechanisms. It is shown that the interactions between the coolant injection and the base over-tip leakage (OTL) flow in the squealer tip region are much stronger in the frontal subsonic region than the rear transonic region. The dominant vortical flow structure is a counter-rotating vortex pair (CRVP) associated with each discrete cooling injection. High HTC stripes on the cavity floor are directly linked to the impingement heat transfer augmentation associated with one leg of the CRVP, which is considerably enhanced by the near-floor fluid movement driven by the overall pressure gradient along the camber line (CAM). The strength of the coolant-base flow interaction as signified by the augmented values of the HTC stripes is seen to correlate to the interplay and balance between the OTL flow and the CRVP structure. As such, for the frontal subsonic part of the cavity, there is a prevailing spanwise inward flow initiated by the CRVP, which has profoundly changed the local base flow, leading to high HTC stripes on the cavity floor. On the other hand, for the rear high speed part, the high inertia of the OTL flow dominates; thus, the vortical flow disturbances associated with the CRVP are largely passively convected, leaving clear signatures on the top surface of the suction surface rim. A further interesting side effect of the strong interaction in the frontal subsonic region is that there is considerable net heat flux reduction (NHFR) in an area seemingly unreachable by the injected coolant. The present results have confirmed that this is due to the large reduction in the local HTC as a consequence of the upstream propagated impact of the strong coolant-base flow interactions.

Understanding the heat transfer of winglet tips is crucial for their applications in high-pressure turbines. The current paper investigates the heat transfer performance of three different winglet-cavity tips in a transonic turbine cascade at a tip gap of 2.1% chord. A cavity tip is studied as the baseline case. The cascade operates at engine representative conditions of an exit Mach number of 1.2 and an exit Reynolds number of 1.7 × 106. Transient infrared thermography technique was used to obtain the tip distributions of heat transfer coefficient for different tips in the experiment. The CFD results were validated with the measured tip heat transfer coefficients, and then used to explain the flow physics related to heat transfer. It is found that on the pressure side winglet, the flow reattaches on the top winglet surface and results in high heat transfer coefficient. On the suction side winglet, the heat transfer coefficient is low near the blade leading edge but is higher from the midchord to the trailing edge. The suction side winglet pushes the tip leakage vortex further away from the blade suction surface and reduces the heat transfer coefficient from 85% to 96% span on the blade suction surface. However, the heat transfer coefficient is higher for the winglet tips from 96% span to the tip. This is because the tip leakage vortex attaches on the side surface of the suction side winglet and results in quite high heat transfer coefficient on the front protrusive part of the winglet. The effects of relative endwall motion between the blade tip and the casing were investigated by CFD method. The endwall motion has a significant effect on the flow physics within the tip gap and near-tip region in the blade passage, thus affects the heat transfer coefficient distributions. With relative endwall motion, a scraping vortex forms inside the tip gap and near the casing, and the cavity vortex gets closer to the pressure side squealer/winglet. The tip leakage vortex in the blade passage becomes closer to the blade suction surface, resulting in an increase of the heat transfer coefficient.

Recent studies have demonstrated that the aerothermal characteristics of turbine rotor blade tip under a transonic condition are qualitatively different from those under a low speed subsonic condition. The cooling injection adds further complexity to the Over-Tip-Leakage (OTL) transonic flow behavior and aerothermal performance, particularly for commonly studied shroudless tip configurations such as a squealer tip. However there has been no published experimental study of a cooled transonic squealer. The present study investigates the effect of cooling injection on a transonic squealer through a closely combined experimental and CFD effort. Part 1 of this two-part paper presents the first of the kind tip cooling experimental data obtained in a transonic linear cascade environment (exit Mach number 0.95). Transient thermal measurements are carried out for an uncooled squealer tip, and six cooling configurations with different locations and numbers of discrete holes. High resolution distributions of heat transfer coefficient and cooling effectiveness are obtained. ANSYS Fluent is employed to perform numerical simulations for all the experimental cases. The mesh and turbulence modeling dependence is first evaluated before further computational studies are carried out. Both the experimental and computational results consistently illustrate strong interactions between the OTL flow and cooling injection. When the cooling injection (even with a relatively small amount) is introduced, distinctive series of stripes in surface heat transfer coefficient are observed with an opposite trend in the chordwise variations on the squealer cavity floor and on the suction surafce rim. Both experimental and CFD results have also consistently shown interesting signatures of the strong OTL flow–cooling interactions in terms of the net heat flux reduction distribution in areas seemingly unreachable by the coolant. Further examinations and analyses of the related flow physics and underlining vortical flow structures will be presented in Part 2.

No abstract