Electrospun nanofiber mesh has previously been used as an air filtration device. However, the qualification of polycaprolactone (PCL) nanofiber mesh cloth in face masks to protect individuals against airborne particles carrying microorganisms has yet to be investigated. The long-term goal of this study is to develop methods to use PCL nanofiber mesh to provide better protection against microorganisms. To achieve this goal, we observed the morphology, water droplet absorption, thermal (differential scanning calorimetry), mechanical, and airborne particle filtering capabilities, and also the microbial activities of a PCL cloth, to evaluate whether it is suitable to act as a filter in a face mask. We have produced a polycaprolactone (PCL) nanofiber cloth after electrospinning it onto a drum for 3 and 10 min, referred to hereafter as PCL-3 and PCL-10, respectively. Our study found that the middle protection layer (control) of the Henry Schein Earloop Procedure Mask contains pores (average diameter = 5.72 ± 0.62 µm) which are 48 times larger than the diameter of a microorganism an average diameter of ~120 nanometers. However, PCL-10 nanofiber membranes show pores with an average diameter of 1.42 ± 0.34 µm. Our contact angle measurement tests found that all the samples were very hydrophobic (contact angle values varied between 120 and 150 degrees). However, both PCL cloths’ contact angle values were lower compared to the control. The produced PCL cloths showed a lower water droplet absorption compared to the control. Thermal studies found that PCL is stable in extreme conditions and no plasticizing effect occurs due to the presence of a solvent. Mechanical tests showed that PCL-10 cloth had higher strength and modulus compared to the control and PCL-3 under tension loading conditions. A vacuum experiment found that the PCL-10 fiber cloth could withstand a negative pressure of 18 Psi without any signs of breakage, and the mask was able to capture airborne particles and microorganisms. The feasibility of immobilizing anti-bacterial nanoparticles with PCL during electrospinning creates the future potential of producing an anti-bacterial face mask using PCL.
The study’s aim was to develop a dermal equivalent scaffold that can mimic the architecture and biological performance of the human dermis. Poly ε-caprolactone (PCL) electrospun nanofiber material (ENF) was assembled with polyethylene glycol diacrylate (PEGDA), sodium alginate (SA) and type I collagen (CG1) to develop three groups of dermal equivalent scaffolds. These scaffolds were named PEGDA-PCL, SA-PCL and CG1-PCL. Scanning electron microscopy (SEM) images of cell-free scaffolds’ top and cross-sectional surface were collected and analyzed to examine internal morphology, specifically the adhesiveness of PCL fibers with the different scaffolds. Human dermal fibroblasts were cultured on each of the scaffolds. Cell viability studies including cell adhesion, cell differentiation and stress fiber production were conducted on each scaffold. Furthermore, the architectural integrity of each scaffold was verified by degradation analysis for 2 weeks by soaking each scaffold in phosphate-buffered saline (PBS) solution. Finally, we conducted rheological characteristics of each scaffold. Based on our results from the above analysis, the study concluded that CG1-PCL is best suitable for the dermal equivalent model and has potential to be used as a graft for skin repair.
Glutathione (GSH) is an anti-inflammatory and antioxidant biomolecule. Polycaprolactone (PCL) nanofiber mesh (NFM) is capable of the attachment and release of biomolecules for prolonged periods and has the potential as a transdermal drug delivery system during wound healing for a diabetic patient. Our earlier study found that high levels of sugar in diabetic male mice were significantly decreased by daily doses of glutathione administered on the mice. Furthermore, oxidative stress found in diabetic male mice led to the total depletion of glutathione levels in the body’s organs (pancreas, spleen, epididymis, and testis). The objective of this study was to attach GSH with PCL NFM for the controlled release of GSH biomolecules for long periods of time from the fiber mesh into a diabetic body. This study produced PCL NFM using an electrospun technique and tested it on mice to evaluate its efficiency as a dermal drug delivery mechanism. This study dissolved GSH (2.5 mg/mL) with phosphate-buffered saline (PBS) and glutaraldehyde (GLU) solution to create GSH-PBS and GSH-GLU complexes. Each complex was used to soak PCL NFM for 24 h and dried to create PCL-GSH-PBS and PCL-GSH-GLU meshes. Fiber morphology, degradation, fibroblast cell proliferation, cytotoxicity, and GSH release activities from each mesh were compared. Fibroblast cell adhesion and cytotoxicity tests found excellent biocompatibility of both GSH-immobilized PCL meshes and no degradation until 20 days of the study period. The disk diffusion method was conducted to test the antibacterial properties of the sample groups. Release tests confirmed that the attachment of GSH with PCL by GSH-GLU complex resulted in a steady release of GSH compared to the fast release of GSH from PCL-GSH-PBS mesh. The disk diffusion test confirmed that PCL-GSH-GLU has antibacterial properties. The above results conclude that GSH-GLU immobilized PCL NFM can be a suitable candidate for a transdermal anti-oxidative and anti-bacterial drug delivery system such as bandage, skin graft for wound healing application in a diabetic patient.
Polyethylene glycol diacrylate (PEGDA) is an important class of photosensitive polymer with many tissue engineering applications. This study compared PEGDA and polycaprolactone (PCL) nanofiber matrix (NFM) coated PEGDA, referred to as PCL-PEGDA, scaffolds for their application in multiple tissue repair such as articular cartilage, nucleus pulposus of the intervertebral disc (IVD). We examined each scaffold morphology, porosity, swelling ratio, degradation, mechanical strength, and in vitro cytocompatibility properties. A defect was created in Sprague Dawley rat tail IVD by scraping native cartilage tissue and disc space, then implanting the scaffolds in the disc space for 4 weeks to evaluate in vivo efficacy of multi-tissue repair. Maintenance of disc height and creation of a new cell matrix was assessed to evaluate each scaffold’s ability to repair the tissue defect. Although both PEGDA and PCL-PEGDA scaffolds showed similar porosity ∼73%, we observed distinct topographical characteristics and a higher effect of degradation on the water-absorbing capacity for PEGDA compared to PCL-PEGDA. Mechanical tests showed higher compressive strength and modulus of PCL-PEGDA compared to PEGDA. In vitro cell studies show that the PCL NFM layer covering PEGDA improved osteoblast cell adhesion, proliferation, and migration into the PEGDA layer. In vivo studies concluded that the PEGDA scaffold alone was not ideal for implantation in rat caudal disc space without PCL nanofiber coating due to low compressive strength and modulus. In vivo results confirm that the PCL-PEGDA scaffold-maintained disc space and created a proteoglycan and collagen-rich new tissue matrix in the defect site after 4 weeks of scaffold implantation. We concluded that our developed PCL-PEGDA has the potential to be used in multi-tissue defect site repair.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.