Objectives Intra-articular injections of local anaesthetics (LA), glucocorticoids (GC), or hyaluronic acid (HA) are used to treat osteoarthritis (OA). Contrast agents (CA) are needed to prove successful intra-articular injection or aspiration, or to visualize articular structures dynamically during fluoroscopy. Tranexamic acid (TA) is used to control haemostasis and prevent excessive intra-articular bleeding. Despite their common usage, little is known about the cytotoxicity of common drugs injected into joints. Thus, the aim of our study was to investigate the effects of LA, GC, HA, CA, and TA on the viability of primary human chondrocytes and tenocytes in vitro . Methods Human chondrocytes and tenocytes were cultured in a medium with three different drug dilutions (1:2; 1:10; 1:100). The following drugs were used to investigate cytotoxicity: lidocaine hydrochloride 1%; bupivacaine 0.5%; triamcinolone acetonide; dexamethasone 21-palmitate; TA; iodine contrast media; HA; and distilled water. Normal saline served as a control. After an incubation period of 24 hours, cell numbers and morphology were assessed. Results Using LA or GC, especially triamcinolone acetonide, a dilution of 1:100 resulted in only a moderate reduction of viability, while a dilution of 1:10 showed significantly fewer cell counts. TA and CA reduced viability significantly at a dilution of 1:2. Higher dilutions did not affect viability. Notably, HA showed no effects of cytotoxicity in all drug dilutions. Conclusion The toxicity of common intra-articular injectable drugs, assessed by cell viability, is mainly dependent on the dilution of the drug being tested. LA are particularly toxic, whereas HA did not affect cell viability. Cite this article : P. Busse, C. Vater, M. Stiehler, J. Nowotny, P. Kasten, H. Bretschneider, S. B. Goodman, M. Gelinsky, S. Zwingenberger. Cytotoxicity of drugs injected into joints in orthopaedics. Bone Joint Res 2019;8:41–48. DOI: 10.1302/2046-3758.82.BJR-2018-0099.R1.

In this study, the bone-regenerative potential of bioactive factors derived from adipose tissue, platelet-rich plasma (PRP) and conditioned medium from hypoxia-treated human telomerase immortalized bone-marrow-derived mesenchymal stem cells (hTERT-MSC) was investigated in vitro with the aim to develop cost-effective and efficient bone substitutes for optimized regeneration of bone defects. Adipose tissue was harvested from human donors undergoing reconstructive surgery, and adipose tissue extract (ATE) was prepared. Platelet lysates (PL) were produced by repeated freeze-thaw cycles of PRP, and hypoxia-conditioned medium (HCM) was obtained by culturing human telomerase immortalized bone-marrow-derived mesenchymal stromal cells for 5 days with 1% O2. Besides analysis by cytokine and angiogenesis arrays, ELISA was performed. Angiogenic potential was investigated in cocultures of bone-marrow-derived (BM)-MSC and human umbilical vein endothelial cells. Multiple angiogenic proteins and cytokines were detected in all growth factor mixtures. HCM and ATE contained high amounts of angiogenin and CCL2/MCP-1, whereas PL contained high amounts of IGFBP-1. Culturing cells with HCM and ATE significantly increased specific ALP activity of BM-MSC as well as tubule length and junctions of endothelial networks, indicating osteogenic and angiogenic stimulation. To achieve a synergism between chemoattractive potential and osteogenic and angiogenic differentiation capacity, a combination of different growth factors appears promising for potential clinical applications.

Magnetic resonance imaging (MRI) is a common clinical practice to visualize defects and to distinguish different tissue types and pathologies in the human body. So far, MRI data have not been used to model and generate a patient-specific design of multilayered tissue substitutes in the case of interfacial defects. For orthopedic cases that require highly individual surgical treatment, implant fabrication by additive manufacturing holds great potential. Extrusion-based techniques like 3D plotting allow the spatially defined application of several materials, as well as implementation of bioprinting strategies. With the example of a typical multi-zonal osteochondral defect in an osteochondritis dissecans (OCD) patient, this study aimed to close the technological gap between MRI analysis and the additive manufacturing process of an implant based on different biomaterial inks. A workflow was developed which covers the processing steps of MRI-based defect identification, segmentation, modeling, implant design adjustment, and implant generation. A model implant was fabricated based on two biomaterial inks with clinically relevant properties that would allow for bioprinting, the direct embedding of a patient’s own cells in the printing process. As demonstrated by the geometric compatibility of the designed and fabricated model implant in a stereolithography (SLA) model of lesioned femoral condyles, a novel versatile CAD/CAM workflow was successfully established that opens up new perspectives for the treatment of multi-zonal (osteochondral) defects. Graphic abstract