No abstract

Optical fibres constitute an exceptional sensing platform. However, standard fibres present an inherent sensing challenge: they confine light to an inner core. Consequently, distributed fibre sensors are restricted to the measurement of conditions that prevail within the core. This work presents distributed analysis of media outside unmodified, standard fibre. Measurements are based on stimulated scattering by guided acoustic modes, which allow us to listen where we cannot look. The protocol overcomes a major difficulty: guided acoustic waves induce forward scattering, which cannot be mapped using time-of-flight. The solution relies on mapping the Rayleigh backscatter contributions of two optical tones, which are coupled by the acoustic wave. Analysis is demonstrated over 3 km of fibre with 100 m resolution. Measurements distinguish between air, ethanol and water outside the cladding, and between air and water outside polyimide-coated fibres. The results establish a new sensor configuration: optomechanical time-domain reflectometry, with several potential applications.

The analysis of surrounding media has been a long-standing challenge of optical fiber sensors. Measurements are difficult due to the confinement of light to the inner core of standard fibers. Over the last two years, new sensor concepts have enabled the analysis of liquids outside the cladding boundary, where light does not reach. Sensing is based on opto-mechanical, forward stimulated Brillouin scattering (F-SBS) interactions between guided light and sound waves. In most previous studies, however, the protective polymer coating of the fiber had to be removed first. In this work, we report the opto-mechanical analysis of liquids outside commercially available, standard single-mode fibers with polyimide coating. The polyimide layer provides mechanical protection but can also transmit acoustic waves from the fiber cladding toward outside media. The comprehensive analysis of opto-mechanical coupling in coated fibers that are immersed in liquid is provided. The model shows that F-SBS spectra in coated fibers are more complex than those of bare fibers and strongly depend on the exact coating diameter and the choice of acoustic mode. Nevertheless, sensing outside coated fibers is demonstrated experimentally. Integrated measurements over 100 m of fiber clearly distinguish between air, ethanol, and water outside polyimide coating. Measured spectra are in close quantitative agreement with the analytic predictions. Furthermore, distributed opto-mechanical time-domain reflectometry mapping of water and ethanol outside coated fiber is reported, with a spatial resolution of 100 m. The results represent a large step toward practical opto-mechanical fiber sensors.

The proper function of protective coating layers is essential for the handling and application of brittle optical fibers. The elastic parameters of polymer coatings can be studied through off-line analysis of test samples. However, the monitoring of these properties on a working fiber during service is challenging. In this work, we use forward stimulated Brillouin scattering processes in standard single mode fibers to measure the acoustic velocity in several types of coating layers. Pump light launches short acoustic pulses outward from the core of the fiber. Multiple reflections at the boundaries between cladding and coating, and between coating and air, form a series of delayed acoustic echoes across the core. These echoes are monitored, in turn, by photo-elastic phase modulation of probe light. Data are collected at temperatures between 25-120 °C. The thermal dependence of the acoustic velocities in several coatings and of the F-SBS resonance frequencies is investigated. Observations are corroborated by calculations. The proposed technique is well suited for research and development of coating materials, production line quality control, reliability studies and preventive maintenance of working fibers.

An opto-electronic radio-frequency oscillator that is based on forward scattering by the guided acoustic modes of a standard single-mode optical fiber is proposed and demonstrated.An optical pump wave is used to stimulate narrowband, resonant guided acoustic modes, which introduce phase modulation to a co-propagating optical probe wave. The phase modulation is converted to an intensity signal at the output of a Sagnac interferometer loop.The intensity waveform is detected, amplified and driven back to modulate the optical pump.Oscillations are achieved at a frequency of 319 MHz, which matches the resonance of the acoustic mode that provides the largest phase modulation of the probe wave. Oscillations at the frequencies of competing acoustic modes are suppressed by at least 40 dB. The linewidth of the acoustic resonance is sufficiently narrow to provide oscillations at a single longitudinal mode of the hybrid cavity. Competing longitudinal modes are suppressed by at least 38 dB as well. Unlike other opto-electronic oscillators, no radio-frequency filtering is required within the hybrid cavity. The frequency of oscillations is entirely determined by the fiber optomechanics. Main TextOpto-electronic oscillators (OEOs) are sources of radio-frequency (RF) tones, which combine optical and electrical paths within a closed-loop, hybrid cavity [1][2][3][4].