Summary This research theoretically investigates the performance of a new integrated solar atmospheric water harvesting system. The system consists of a concentrated photovoltaic thermal unit (CPV/T) to capture solar radiation and produce electricity. The rejected heat is utilized to drive an alpha‐type Stirling engine and a single effect LiBr/H2O absorption cooling cycle (ACC). The power output of the Stirling engine and the CPV/T is used to drive a vapor compression refrigeration cycle (VCRC), whereas the cooling capacity of the cooling cycles is used to cool and dehumidify ambient air and generate potable water. Moreover, a heat recovery heat exchanger is employed to pre‐cool the supply air before entering the evaporator, thus increasing the water production rate. The model is validated and solved numerically. A parametric study is conducted to show the effect of a variety of ambient and operating conditions on the system's performance. The highest water production rate is found, as expected, to be in hot and humid climates where the solar radiation, the ambient temperature, and the relative humidity are high. The freshwater production exhibits a non‐monotonic behavior with increasing the air mass flow rate, and the maximum potable water production was identified. At solar radiation values of 0.6, 0.8, and 1 (kW/m2), the maximum water production was generated at air mass flow rate values of 1.6, 2.8, and 3.8 (kg/s), and the corresponding maximum water production were 13.37, 20.12, and 26.28 (L/h), respectively. It is found that this integrated system can produce up to 30 L/h under hot and humid ambient conditions, and pre‐cooling of the supplied air yields better performance under drier conditions. The proposed system is suitable for small‐scale applications where water demand is less than 180 L/day. It is found that the amount of electrical energy consumed per liter of produced water by this system is between 225 and 315 Wh/L approximately.

High Entropy Alloys (HEAs) and Refractory High-Entropy Alloys (RHEAs) are novel potential materials for high-temperature applications [1]. NbMoTaW, a RHEAs, such as the one in Fig. 1, possess superior mechanical properties, combining high strength, outstanding thermal stability, and resistance to softening at high temperatures [2]. The influence of adding Vanadium [3], Tantalum [4], and Rhenium [5] to NbMoTaW alloys on the bulk mechanical behavior was investigated by the previous studies. In this research, the effect of adding Rhenium with different (Re0, Re0.5, Re1) on the microstructure and the mechanical properties of NbMoTaW thin films will be nvestigated. The larger the enthalpy of mixing in negative values, the higher the binding force between the elements, which has been enhanced with Rhenium addition. As for the entropy of mixing, it increased from 11.53 to 13.38 for Re0 and Re1, respectively. The higher the mixture entropy suggests a more stable solid solution. This is confirmed by calculating the thermodynamic parameters proposed by Yang et. Al [6] where they suggested that a mixture with δ < 6.6 and Ω > 1.1 correspond to solid solution formation. The anticipated crystal structure for the three samples is BCC structure according to the valence electron concentration (VEC) theory, where the VEC values were less than 6.87 as suggested by Gou et. Al [7]. The RexNbMoTaW HEAs thin films are fabricated using RF magnetron sputtering. The film thickness, deposition power, and temperature impact on the films’ characteristics are studied. Field emission (FE-SEM), X-ray diffraction (XRD), and nanoindentation are used to investigate the RexNbMoTaW thin films’ crystal structure, surface morphology, and mechanical properties. The mechanical properties of the thin films will be compared with their counterpart bulk materials. References Kim, H., et al., International Journal of Refractory Metals and Hard Materials, 2019. 80: p. 286-291. Feng, X., et al., Materials Letters, 2018. 210: p. 84-87. Senkov, O.N., et al., Intermetallics, 2011. 19(5): p. 698-706. Han, Z.D., et al., Materials Science and Engineering: A, 2018. 712: p. 380-385. Zhang, J., et al., Journal of Alloys and Compounds, 2020. 827. Yang, X. and Y. Zhang, Materials Chemistry and Physics, 2012. 132(2-3): p. 233-238. Guo, S., et al., Journal of Applied Physics, 2011. 109(10): p. 103505. Figure 1