No abstract

No abstract

The paper is devoted to the development of an asymptotic approach to solution of the steady isothermal problem of elastohydrodynamic lubrication (EHL) for heavily loaded point contacts. It is shown that the whole contact region can be subdivided into three subregions: the central one that is adjacent to the other two regions occupied by the ends of the horseshoe-shaped pressure/gap distribution zone. The central region, in turn, can be subdivided into the Hertzian region and its adjacent inlet and exit zones that, in turn, are adjacent to the inlet and exit boundaries of the contact, respectively. Moreover, in the central region, in the inlet and exit zones of heavily loaded point EHL contact, the EHL problem can be reduced to asymptotically valid equations identical to the ones obtained in the inlet and exit zones of heavily loaded line EHL contacts. The latter means that many of the well-known properties of heavily loaded line EHL contacts are also valid for heavily loaded point EHL contacts. These asymptotically valid equations can be analysed and numerically solved based on the stable methods using a specific regularisation approach that were developed for lubricated line contacts. Cases of pre-critical and over-critical lubrication regimes are considered. The by-product of this asymptotic analysis is an easy analytical derivation of formulas for the lubrication film thickness for pre-critical and over-critical lubrication regimes. The method is validated by the results of some experimental and numerical studies published by a number of researches.

To obtain stable solutions of asymptotic equations in the inlet and exit zones of a heavily loaded isothermal EHL contact we will employ a regularisation technique which follows from the asymptotic analysis conducted in Parts 1 and 2 of this paper. This regularisation provides stable numerical solutions in a very wide range of parameters which covers the whole practical range of EHL parameters. The success in regularisation of asymptotic equations is extended on the original equations of the isothermal EHL problem. The numerical scheme for regularised original equations of the isothermal EHL problem is developed. Some numerical examples of regularised solutions are presented. It is shown that the regularisation approach works well and produces stable numerical solutions for very large pressure viscosity coeffi cients. Copyright

Over the last couple decades coatings attract more and more attention in practical applications. The present study addresses a question which is not well studied: how coated surfaces behave in lubricated contacts? In other words, this is a study of the effectiveness of functionally graded materials in heavily loaded point elastohydrodynamically lubricated contacts with straight lubricant entrainment. As a part of the study, some criteria of coating effectiveness are introduced and discussed. More specifically, the behavior of main parameters such as the lubrication film thickness and the frictional force in point heavily loaded lubricated contacts of functionally graded elastic materials are considered. The problem is studied based on the method of matched asymptotic expansions which allows us to split the problem into two separate problems: a dry contact problems for functionally graded elastic materials and an elastohydrodynamically lubricated problem for functionally graded materials. The elastohydrodynamically lubricated problem uses as input data not only the operational and physical parameters of the materials and lubricant but also the asymptotic behavior of the dry contact problem solution near the contact boundaries. Therefore, a sequence of two problems must be solved: the dry contact problems for functionally graded elastic materials and the elastohydrodynamically lubricated problem for functionally graded materials. Similar methods have been used for the analysis of an elastohydrodynamically lubricated problem for heavily loaded line contacts of functionally graded materials. The dry contact problem will be analyzed in Part 1 of the paper based on a semi-analytical bilateral method which produces correct asymptotic solutions for thin and thick coatings. The analytical expressions for contact pressure are obtained and analyzed for various combinations of coating thicknesses and elastic properties. The elastohydrodynamically lubricated problem will be considered in Part 2 of the paper based on the method of matched asymptotic expansions. In the analysis of the elastohydrodynamically lubricated problem, as in the case of homogeneous contact materials, it is shown that the whole contact region can be subdivided into three subregions: the central one which is adjacent to the other two regions occupied by the ends of the zones. The central region can be subdivided into the Hertzian region and then adjacent to it inlet and exit zones which, in turn, are adjacent to the inlet and exit boundaries of the contact, respectively. In the Hertzian region the elastohydrodynamically lubricated problem solution is very close to the solution of the corresponding dry (i.e. non-lubricated) contact problem for functionally graded elastic materials which have been analyzed. In the central region in the inlet and exit zones of a heavily loaded point elastohydrodynamically lubricated contact, the elastohydrodynamically lubricated problem for functionally graded elastic materials using certain scaling transforms can be reduced...