No abstract

We generate attosecond pulse train (APT) in argon driven by the high repetition rate (HR) laser of the extreme light infrastructure-attosecond light pulse source (ELI-ALPS), providing 100 kHz, 80 W, 1030 nm, 40 fs pulses from a fiber chirped-pulse amplification (fiber-CPA) laser system. Under the current operating conditions of the high harmonic generation beamline (HR-GHHG), we observed the average pulse duration to be 395 as measured using the technique of reconstruction of attosecond beating by interference of two-photon transitions. The beamline uses an annular-shape laser beam so that the main part of the driving laser co-propagating with the APT can be eliminated by reflection on a holey mirror. An additional 100 nm aluminum foil is used to filter out the remaining laser and the low order harmonics, allowing 2 pJ APT with a bandwidth from 25 eV to 50 eV to be transported to the target position where the APT interacts with matter. The implementation of the HR-GHHG beamline in ELI-ALPS delivering attosecond pulse trains at 100 kHz paves the way for time-resolved experiments in the infrastructure, especially those that involve rare events and coincidence analysis, both of which need high statistics.

High-repetition rate attosecond pulse sources are indispensable tools for time-resolved studies of electron dynamics, such as coincidence spectroscopy and experiments with high demands on statistics or signal-to-noise ratio, especially in the case of solid and big molecule samples in chemistry and biology. Although with the high-repetition rate lasers, such attosecond pulses in a pump-probe configuration are possible to achieve, until now, only a few such light sources have been demonstrated. Here, by shaping the driving laser to an annular beam, a 100 kHz attosecond pulse train (APT) is reported with the highest energy so far (51 pJ/shot) on target (269 pJ at generation) among the high-repetition rate systems (>10 kHz) in which the attosecond pulses were temporally characterized. The on-target pulse energy is maximized by reducing the losses from the reflections and filtering of the high harmonics, and an unprecedented 19% transmission rate from the generation point to the target position is achieved. At the same time, the probe beam is also annular and low loss of this beam is reached by using another holey mirror to combine with the APT. The advantages of using an annular beam to generate attosecond pulses with a high-average power laser are demonstrated experimentally and theoretically. The effect of nonlinear propagation in the generation medium on the annular-beam generation concept is also analyzed in detail.

Attosecond Pulse Trains (APT) generated by high-harmonic generation (HHG) of high-intensity near-infrared (IR) laser pulses have proven valuable for studying the electronic dynamics of atomic and molecular species. However, the high intensities required for high-photon-energy, high-flux HHG usually limit the class of adequate laser systems to repetition rates below 10 kHz. Here, APT's generated from the 100 kHz, 160 W, 40 fs laser system (HR1) of the Extreme Light Infrastructure Attosecond Light Pulse Source (ELI-ALPS) are reconstructed using the Reconstruction of Attosecond Beating By Interference of two-photon Transitions (RABBIT) technique. These experiments constitute the first attosecond time-resolved photoelectron spectroscopy measurements performed at 100 kHz repetition rate and the first attosecond experiments performed at ELI-ALPS. These RABBIT measurements were taken with an additional IR field temporally locked to the extremeultraviolet APT, resulting in an atypical ω beating. We show that the phase of the 2ω beating recorded under these conditions is strictly identical to that observed in standard RABBIT measurements within second-order perturbation theory. This work highlights an experimental simplification for future experiments based on attosecond interferometry (or RABBIT), which is particularly useful when lasers with high average powers are used.

Two-stage multipass-cell compression of a fiber–chirped-pulse amplifier system to the few-cycle regime is presented. The output delivers a sub-2-cycle (5.8 fs), 107 W average power, 1.07 mJ pulses at 100 kHz centered at 1030 nm with excellent spatial beam quality (M2 = 1.1, Strehl ratio S = 0.98), pointing stability (2.3 µrad), and superior long-term average power stability of 0.1% STD over more than 8 hours. This is combined with a carrier-envelope phase stability of 360 mrad in the frequency range from 10 Hz to 50 kHz, i.e., measured on a single-shot basis. This unique system will serve as an HR1 laser for the Extreme Light Infrastructure Attosecond Light Pulse Source research facility to enable high repetition rate isolated attosecond pulse generation.