No abstract

The voltage response to pulsed uniform magnetic fields and the accompanying bending deformations of laminated cantilever structures are investigated experimentally in detail. The structures comprise a magnetoactive elastomer (MAE) slab and a commercially available piezoelectric polymer multilayer. The magnetic field is applied vertically and the laminated structures are customarily fixed in the horizontal plane or, alternatively, slightly tilted upwards or downwards. Six different MAE compositions incorporating three concentrations of carbonyl iron particles (70 wt%, 75 wt% and 80 wt%) and two elastomer matrices of different stiffness are used. The dependences of the generated voltage and the cantilever’s deflection on the composition of the MAE layer and its thickness are obtained. The appearance of the voltage between the electrodes of a piezoelectric material upon application of a magnetic field is considered as a manifestation of the direct magnetoelectric (ME) effect in a composite laminated structure. The ME voltage response increases with the increasing total quantity of the soft-magnetic filler in the MAE layer. The relationship between the generated voltage and the cantilever’s deflection is established. The highest observed peak voltage around 5.5 V is about 8.5-fold higher than previously reported values. The quasi-static ME voltage coefficient for this type of ME heterostructures is about 50 V/A in the magnetic field of ≈100 kA/m, obtained for the first time. The results could be useful for the development of magnetic field sensors and energy harvesting devices relying on these novel polymer composites.

Surface topographical modifications of a soft magnetoactive elastomer (MAE) in response to variable applied magnetic field are investigated. The analysis is performed insitu and is based on optical microscopy, spread optical reflection and optical profilometry measurements. Optical profilometry analysis shows that the sensitivity of magnetic fieldinduced surface roughness with respect to external magnetic field is in the range of 1 µm/T. A significant hysteresis of surface modifications takes place for increasing and decreasing fields. Investigations of shape of sessile water droplets deposited on the MAE surface reveal that field-induced topographical modifications affect the contact angle of water at the surface. This effect is reversible and the sensitivity to magnetic field is in the range of 20/T.

A simple method for structuring of the surface of a magnetoactive elastomer (MAE) on the tens of micrometers scale, which capabilities extend beyond conventional mold‐based polymer casting, is reported. The method relies on the ablation of the material by absorption of nanosecond infrared pulses from a commercial laser. It is shown that it is possible to fabricate parallel lamellar structures with a high aspect ratio (up to 6:1) as well as structures with complex scanning trajectories. The method is fast (fabrication time for the 7 × 7 mm2 is about 60 s), and the results are highly reproducible. To illustrate the capabilities of the fabrication method, both orthogonal to the MAE surface and tilted lamellar structures are fabricated. These magnetosensitive lamellae can be easily bent by ±45° using an external magnetic field of about 230 mT. It is demonstrated that this bending allows one to control the sliding angle of water droplets in a great range between a sticky (>90°) and a sliding state (<20°). Perspectives on employing this fabrication technology for magnetosensitive smart surfaces in microfluidic devices and soft robotics are discussed.

Elongations of magnetoactive elastomers (MAEs) under ascending–descending uniform magnetic fields were studied experimentally using a laboratory apparatus specifically designed to measure large extensional strains (up to 20%) in compliant MAEs. In the literature, such a phenomenon is usually denoted as giant magnetostriction. The synthesized cylindrical MAE samples were based on polydimethylsiloxane matrices filled with micrometer-sized particles of carbonyl iron. The impact of both the macroscopic shape factor of the samples and their magneto-mechanical characteristics were evaluated. For this purpose, the aspect ratio of the MAE cylindrical samples, the concentration of magnetic particles in MAEs and the effective shear modulus were systematically varied. It was shown that the magnetically induced elongation of MAE cylinders in the maximum magnetic field of about 400 kA/m, applied along the cylinder axis, grew with the increasing aspect ratio. The effect of the sample composition is discussed in terms of magnetic filler rearrangements in magnetic fields and the observed experimental tendencies are rationalized by simple theoretical estimates. The obtained results can be used for the design of new smart materials with magnetic-field-controlled deformation properties, e.g., for soft robotics.